PCI Data Acquisition I/O Product List

PCI/PCIe I/O Products

         Product          Description Notes
       Concurrent Real-Time A/D and PWM
CP-AD3224-DS32-channel, 24-bit Delta-Sigma PCIe analog input card with up to 216 KSPS sample rate per channel. Features include: 32-channel fully differential with +/-5V interface, A/D converter per channel, Industry standard SCSI 68-pin connector for inputs, PCI Express x1 Revision 1.0a, Independent clocking for four channel groups, Low-jitter phase lock loop (PLL) clock generators, Multi-board clocking and synchronization, Directly addressable conversion data registers, 64K word conversion data FIFO with DMA, Low-noise analog power generation, Positive and negative calibration voltage, Positive and negative calibration coefficients, Differential input impedance: >200K ohm, Input over-voltage protection: +/-30V @ <150 milliamps, Input over-current protection: 150 milliamps fused, Sampling rate (Fs): 2 Khz to 216 Khz, Multiple sampling rates per 8-channel group. 
CP-PWM-101212-line Pulse Width Modulation (PWM) Output PCIe card. Autonomously generates TTL pulse width modulated (PWM) signals with high accuracy. Provides a timing resolution of 50 ns and the ability to program sine frequencies, PWM frequencies, dead-band and duty cycle in real time. Provides 12 digital output lines with 5V TTL output (TI 74ABT16240 driver). The card features 34K logical FPGA elements and high-speed PLL-generated clocks at 100MHz+. Multiple cards are supported per system. Occupies a PCIe x1 slot or higher. Provides FPGA-based PWM board, TTL outputs, 3 modes of operation (12 outputs) including 2-channel 3-phase complementary PWM outputs, 1-channel 6-phase complementary PWM outputs and 12-channel PWM outputs. Provides 12-bit PWM signal resolution, Programmable sine wave frequency, PWM frequency, duty cycle and dead band, 66 MHz board frequency, 20 MHz PWM base frequency (timing resolution of 50 ns), External Connectors: Molex LFH-60, Power Consumption: ~5 watts. 
CP-PWM-111212-line Pulse Width Modulation (PWM) Input PCIe card. Designed for capturing pulse width modulated signals with high accuracy. Features a timing resolution of 15.15 nanoseconds and the ability to measure the frequency and duty cycle. Provides 12 digital input lines with 5V TTL input (74LVCH16240 driver). The card features 34K logical FPGA elements and high-speed PLL-generated clocks at 100MHz+. Multiple cards are supported per system. The card occupies a PCIe x1 slot or higher. Features include FPGA-based PWM input board, 12 channel TTL inputs, 32-bit resolution, 66 MHz board frequency, 66 MHz PWM measurement base frequency, Minimum pulse width of 15.15 nsec, Minimum period of 30.30 nsec, Pulse-width/period accuracy of 2 internal clock cycles (30.30 nsec), Measurement frequency range of 1Hz to 20 MHz, Measurement duty cycle of 0-100%, External Connectors: Molex LFH-60, Power Consumption: ~5 watts. 
       Acromag Industry Pack
CS-ACRO-5025-288 Termination Panel for the CS-ACRO-APC730 PCI device. DIN Rail Mount, 68 screw terminals, SCSI-3 connector Cable not included.  
CS-ACRO-5028-432 Shielded Cable for the CS-ACRO-APC730 PCI device. SCSI-3 68-pin connector.  
CS-ACRO-APC730 Multi-Functin I/O: Analog In: 16 differential or 32 single-ended inputs (±3.3V, ±5V, ±10V, 0-5V, and 0-10V ranges) 16-bit ADC with 512 sample RAM; Analog Out: Eight analog output channels (±10V range), Individual 16-bit DACs per channel, 1024 sample FIFO for waveform generation; Digital I/O:16 TTL bidirectional input/outputs; Counter/Timer: One 32-bit counter/timer.  
CS-ACRO-APC8620 PCI Carrier Card for 5 IP Modules (requires 5V PCI slot) (THIS BOARD IS NO LONGER AVAILABLE AND IS REPLACED BY THE CS-ACRO-APC8620A Model) This item can no longer be provided by Concurrent. Please refer to the CS-ACRO-APC8620A model. 
CS-ACRO-APC8620A PCI bus(PC)carrier board, non-intelligent PCI bus carrier, holds 5 IPack modules(full length); plug-and-play carrier configuration and interrupt support, standard IP module interface, supports two interrupt channels per IP, accepts other manufactures' IP modules Driver support only for the IP330/IP480-2/IP480-6/IP520-64. If different IP modules are required, please contact salesman for quotation. 
CS-ACRO-IP330 16-bit A/D IP Module (32 SE or 16 Diff. Ch) Requires purchase of CS-ACRO-APC-8620A 
CS-ACRO-IP480-2 Two 16-bit (one 32-bit) Counter/Timers IP Module Requires purchase of CS-ACRO-APC-8620A 
CS-ACRO-IP480-6 Six 16-bit (three 32-bit) Counter/Timers IPModule Requires purchase of CS-ACRO-APC-8620A 
CS-ACRO-IP520-64 Eight RS-232E Serial Port IP Modules Requires purchase of CS-ACRO-APC-8620A 
       ADLINK Relay/DI
CS-AL-ACL-10569-2 (Adlink ACL-10569-2) -2M SCSI 68 to 68 Cable for the CS-AL-P7256  
CS-AL-DIN-68S-1 (Adlink DIN-68S-1) - General purpose termination board for 68-pin SCSI -II cable for the CS-AL-P7256. Dimensions: 103 mm x 83 mm x 43 mm (W x L x H).  
CS-AL-P7256 16-CH Latching SPDT Relay Outputs & 16-CH Isolated DI Card, COS Interrupt. Supports a 32-bit 3.3 V or 5 V PCI bus ( Adlink p/n PCI-7256)  
       AIM USA AFDX/ARINC 664
CS-AM-API-FDX-2 AIM API-FDX-2 Dual Channel AFDX/ARINC 664 Dual Port PCI Device  
       Commtech Serial
CS-CM-F422-4-335 Commtech Fastcom: 422/4-PCI-335 - 4-ports, RS422 & RS485 Async Only. Vendor Listed Specifications: Maximum serial data rate of 6.25 Mbps, 17D154 UART, Universal PCI (3.3V & 5V). Unless non-standard baud rates are required, Concurrent recommends purchase of the MOXA CS-MX-CPXXX serial products. Note: This device does not support Synchronous communications - This is an Async only device. Includes DB37 plug to four DB9 receptacles. (**TECHNICAL CONDITIONS**) Requires RedHawk Server Linux Release 5.4 or higher, a custom kernel is required to support this device and it will not function in an external PCI expansion chassis. (MFG p/n 422/4-PCI-335)  
CS-CM-SuperFSCC-4 Commtech SuperFSCC/4 - 4-ports, RS422 & RS485 Synchronous support only. Vendor listed specifications: Maximum serial data rates 12.5 Mbits/s DPLL, 30 Mbits/s external, 50 Mbits/s internal clock, CP711A UART, Universal PCI (3.3V & 5V). Includes Two 0.8mm Champ connectors to four DB25 plugs. (**NOTE**) It has been found that this device's Asynchronous support is non-functional and therefore Concurrent cannot support asynchronous communications with this device (please see the General Standards CS-GS-SIO4B family or MOXA CS-MX-CPXXX family of serial I/O devices for asynchronous support). (MFG p/n SuperFSCC/4)  
       Comtrol Serial
CS-CT-30002-1 8-Port RocketPort INFINITY Octacable RJ45 - Serial adapter - PCI-X - RS-232, RS-422, RS-485 - Includes 8-port RJ45 cable assembly. NOTE: The Comtrol driver performs polling I/O only and as such, latencies of 30ms or more have been measured, Real-Time performance cannot be guaranteed.  
CS-CT-30010-6 32 Port RocketPort Infinity RS232/422/485 PCI-X device (5V/3.3V PCI Slot Compatible) (RoHS) (Requires Two CS-CT-3c0030-4 16-Port Interface Panel) NOTE: The Comtrol driver performs polling I/O only and as such, latencies of 30ms or more have been measured, Real-Time performance cannot be guaranteed.  
CS-CT-30015-1 16 Port RocketPort Infinity RS232/422/485 PCI-X device (5V/3.3V PCI Slot Compatible) (RoHS) (Requires One CS-CT-3c0030-4 16-Port Interface Panel ) NOTE: The Comtrol driver performs polling I/O only and as such, latencies of 30ms or more have been measured, Real-Time performance cannot be guaranteed.  
CS-CT-30020-5 8 Port RocketPort Infinity RS232/422/485 PCI-X device (5V/3.3V PCI Slot Compatible) (RoHS) (Requires One CS-CT-3c0040-3 8-Port Interface Panel) NOTE: The Comtrol driver performs polling I/O only and as such, latencies of 30ms or more have been measured, Real-Time performance cannot be guaranteed.  
CS-CT-30126-4 RocketPort EXPRESS Quadcable DB9M is a four port serial adapter PCI Express 4-Port serial card with DB9M fanout cable, communication speeds up to 921 Kbps, PCI Express serial x1, x2, x4, x8, x12 and x16 lane connectivity, RS-232, RS-422, RS-485 software-selectable serial ports (Vendor p/n 30126-4)  
CS-CT-30127-1 RocketPort EXPRESS Quadcable DB25M is a four port serial adapter PCI Express 4-Port serial card with DB9M fanout cable , communication speeds up to 921 Kbps, PCI Express serial x1, x2, x4, x8, x12 and x16 lane connectivity, RS-232, RS-422, RS-485 software-selectable serial ports (Vendor p/n 30127-1)  
CS-CT-3c0030-4 RocketPort Infinity 16 port DB9 Male Interface Panel. (Note: Used by the 16 and 32 Port RocketPort Infinity Devices CS-CT-30020-5 & CS-CT-30010-6.) Comtrol P/N 30030-4.  
CS-CT-3c0040-3 RocketPort Infinity 8 port DB9 Male Interface Panel. (Note: Used by the 8 Port RocketPort Infinity Device CS-CT-30020-5.) Comtrol P/N 30040-3  
CS-CT-98295-1 Comtrol RocketPort USB Serial Hub II - Serial adapter - Hi-Speed USB - RS-232 - serial - 4 ports  
CS-CT-98296-8 Comtrol RocketPort USB Serial Hub III - Serial adapter - USB - RS-232 - serial - 8 ports  
CS-CT-99341-4 RocketPort Universal PCI-Quad 4-Channel RS232 DB9M PCI Adapter (5V/3.3V PCI Slot Compatible) (RoHS) (Replaces CS-CT-99095-6) NOTE: The Comtrol driver performs polling I/O only and as such, latencies of 30ms or more have been measured, Real-Time performance cannot be guaranteed.  
CS-CT-99342-1 RocketPort Universal PCI-Octa 8-port RS232 DB9M (5V/3.3V PCI Slot Compatible) (RoHS) (Replaces CS-CT-99096-3) NOTE: The Comtrol driver performs polling I/O only and as such, latencies of 30ms or more have been measured, Real-Time performance cannot be guaranteed.  
CS-CT-99343-8 RocketPort Universal PCI-Quad 4-Channel RS232 DB25M PCI Adapter (5V/3.3V PCI Slot Compatible) (RoHS) (Replaces CS-CT-99097-0) NOTE: The Comtrol driver performs polling I/O only and as such, latencies of 30ms or more have been measured, Real-Time performance cannot be guaranteed.  
CS-CT-99344-5 RocketPort Universal PCI-Octa 8-port RS232 DB25M (5V/3.3V PCI Slot Compatible) (RoHS) (Replaces CS-CT-99098-7) NOTE: The Comtrol driver performs polling I/O only and as such, latencies of 30ms or more have been measured, Real-Time performance cannot be guaranteed.  
CS-CT-99345-2 RocketPort Universal PCI-Octa 8-port RS232 RJ45 (5V/3.3V PCI Slot Compatible) (RoHS) (Replaces CS-CT-99099-4) NOTE: The Comtrol driver performs polling I/O only and as such, latencies of 30ms or more have been measured, Real-Time performance cannot be guaranteed.  
CS-CT-99355-1 RocketPort Universal PCI-16 Port RS232/422 on each port (5V/3.3V PCI Slot Compatible). Requires a 16-port External Universal Interface (CS-CT-P-99360-5) (RoHS) (Replaces CS-CT-99125-0) NOTE: The Comtrol driver performs polling I/O only and as such, latencies of 30ms or more have been measured, Real-Time performance cannot be guaranteed.  
CS-CT-99365-0 RocketPort Universal PCI-8 Port Low Profile (5V/3.3V PCI Slot Compatible). Requires an 8-port External Universal Interface (CS-CT-99370-4) (RoHS) (Replaces CS-CT-99110-6) NOTE: The Comtrol driver performs polling I/O only and as such, latencies of 30ms or more have been measured, Real-Time performance cannot be guaranteed.  
CS-CT-99370-4 8-port RS232/422 DB25 Female External Universal Interface Connector Panel. For use with CS-CT-99365-0. (RoHS) (Replaces CS-CT-95050-9) NOTE: The Comtrol driver performs polling I/O only and as such, latencies of 30ms or more have been measured, Real-Time performance cannot be guaranteed. This item is is the replacement for the now obsolete CS-CT-95050-9) due to RoHS requirements. 
CS-CT-99375-9 8-port RS232 External Universal Interface DB25 Female Connector Panel. For use with CS-CT-99365-0. (RoHS) (Replaces CS-CT-94050-0) NOTE: The Comtrol driver performs polling I/O only and as such, latencies of 30ms or more have been measured, Real-Time performance cannot be guaranteed.  
CS-CT-99385-8 8-port RS232/422 DB25 Male External Universal Interface Connector Panel. For use with CS-CT-99365-0. (RoHS) (Replaces CS-CT-97050-7) NOTE: The Comtrol driver performs polling I/O only and as such, latencies of 30ms or more have been measured, Real-Time performance cannot be guaranteed.  
CS-CT-P-99360-5 16-port RS232/422 DB25 Female External Universal Interface Connector Panel. For use with CS-CT-99355-1 (RoHS) (Replaces CS-CT-95100-1) NOTE: The Comtrol driver performs polling I/O only and as such, latencies of 30ms or more have been measured, Real-Time performance cannot be guaranteed.  
CS-DD-400I-180-JL0 DD-40100I180R-JL0: PCI ARINC 429/717 18 Channels that can be individually programmed for Transmit/Receive functionality with parametric test features, variable output voltage, and voltage monitoring on board. 0°C to +55°C, PCI 32-bit, 33/66MHz PCI Local Bus Rev. 2.2 compliant. Front I/O.  
CS-DD-401F-180-3L0 DD-40000F180R-3L0: PMC ARINC 429/717 18 Channels that can be individually programmed for Transmit/Receive functionality with parametric test features, variable output voltage, and voltage monitoring on board. 0°C to +71°C, PCI 32-bit, 33/66MHz PCI Local Bus Rev. 2.2 compliant. Front I/O.  
CS-DD-401K-180-3L0 DD-40000K180R-3L0: PCIe ARINC 429/717 18 Channels that can be individually programmed for Transmit/Receive functionality with parametric test features, variable output voltage, and voltage monitoring on board. 0°C to +71°C, PCIe x1 Rev 1.1 compliant. Front I/O.  
CS-DD-42916I3-300 (DISCONTINUED) DDC PCI ARINC 429 with 16 independent programmable receiver/transmitter, high/low speed ARINC channels with receive label/SDI data filtering and data time stamping; on-board processor for engineering unit conversions and data processing, dual-port RAM. Note: This is a PMC device (DD-42916C1-300 ) -supplied on a PCI/PMC Carrier. (This ARINC 429 device is supported with SWB - License ICS-SWB-211 is required). Please use the CS-DD-400I-180-JL0 18 Channel ARINC 429 PCI device or the CS-DD-401K-180-3L0 18 Channel ARINC 429 PCIe device for all new orders. 
CS-DD-42916I3E-300 (DISCONTINUED) DDC PCIe ARINC 429 with 16 independent programmable receiver/transmitter, high/low speed ARINC channels with receive label/SDI data filtering and data time stamping; on-board processor for engineering unit conversions and data processing, dual-port RAM. Note: This is a PMC device (DDC p/n DD-42916C1-300) supplied on a GS PCIe1-to-PMC-ADAPTER-0 Carrier (CS-GS-PMC2PCIE1). (This ARINC 429 device is supported with SWB - License ICS-SWB-211 is required).  
CS-DD-65569I1-300 MIL-STD-1553 w/ 1 Dual Redundant Device - Enhanced mini-ace supports BC/RT/MT bus functions. Note - This is an older design board. See CS-DD-671X06-XXXX for current design 1553 devices. (DDC p/n BU65569I1-300)  
CS-DD-65569I2-300 MIL-STD-1553 w/ 2 Dual Redundant Devices - Enhanced mini-ace supports BC/RT/MT bus functions. Each channel may be independently programmed for BC/RT/Monitor or RT/Monitor mode. Note - This is an older design board. See CS-DD-671X06-XXXX for current design 1553 devices. (DDC p/n BU65569I2-300)  
CS-DD-65569I3-300 MIL-STD-1553 w/ 3 Dual Redundant Devices - Enhanced mini-ace supports BC/RT/MT bus functions. Each channel may be independently programmed for BC/RT/Monitor or RT/Monitor mode. Note - This is an older design board. See CS-DD-671X06-XXXX for current design 1553 devices. (DDC p/n BU65569I3-300)  
CS-DD-65569I4-300 MIL-STD-1553 w/ 4 Dual Redundant Devices - Enhanced mini-ace supports BC/RT/MT bus functions. Each channel may be independently programmed for BC/RT/Monitor or RT/Monitor mode. Note - This is an older design board. See CS-DD-671X06-XXXX for current design 1553 devices. (DDC p/n BU65569I4-300)  
CS-DD-65570I1-300 ***This device is End-of-Life (EOL)*** Please use the CS-DD-67X06K-X00R device as an alternative. Single Dual-Redundant MIL-STD-1553B Channel. Can simultaneously simulate a Bus Controller (BC), up to 31 Remote Terminals (RTs), and provides a selectable, triggerable Bus Monitor (MT) for each bus. (Fixed Voltage 20Vp-p Nominal)  
CS-DD-65570I2-300 ***This device is End-of-Life (EOL)*** Please use the CS-DD-67X06K-X00R device as an alternative. Two Dual-Redundant MIL-STD-1553B Channels. Can simultaneously simulate a Bus Controller (BC), up to 31 Remote Terminals (RTs), and provides a selectable, triggerable Bus Monitor (MT) for each bus. (Fixed Voltage 20Vp-p Nominal)  
CS-DD-65572I1-300 *** This item is nearing End-of-Life (EOL) *** and should not be used for new applications. Please use the CS-DD-67X06K-X00R device as an alternative. Single Dual-Redundant MIL-STD-1553B Channel. Can simultaneously simulate a Bus Controller (BC), up to 31 Remote Terminals (RTs), and provides a selectable, triggerable Bus Monitor (MT) for each bus. (Variable Voltage 0V - 21.5V p-p)  
CS-DD-65572I2-300 *** This item is nearing End-of-Life (EOL) *** and should not be used for new applications. Please use the CS-DD-67X06K-X00R device as an alternative. Two Dual-Redundant MIL-STD-1553B Channels. Can simultaneously simulate a Bus Controller (BC), up to 31 Remote Terminals (RTs), and provides a selectable, triggerable Bus Monitor (MT) for each bus. (Variable Voltage 0V - 21.5V p-p)  
CS-DD-67106K-100R DDC BU-67106K-100R-JLO (Single Function) PCI Express (x1) MIL-STD-1553 device. Single dual redundant MIL-STD-1553 channels operating modes are BC/Monitor or Multi-RT/Monitor. The card also contains software configurable bus coupling and termination options, eight digital discrete I/Os, eight avionics (+35V) Discrete I/Os, IRIG-B Time Code Input/Output, and a Time Tag Clock Input/Output. Commercial Temp. (This 1553 device is supported with SWB - License ICS-SWB-225 is required). Supported by RedHawk and SimWB. 
CS-DD-67106K-200R DDC BU-67106K-200R-JLO PCI Express (x1) MIL-STD-1553 device. Two dual redundant MIL-STD-1553 channels operating modes are BC/Monitor or Multi-RT/Monitor. Each mode has the ability to run a concurrent Bus Monitor (MT). The card also contains software configurable bus coupling and termination options, eight digital discrete I/Os, eight avionics (+35V) Discrete I/Os, IRIG-B Time Code Input/Output, and a Time Tag Clock Input/Output. Commercial Temp. (This 1553 device is supported with SWB - License ICS-SWB-225 is required). Supported by RedHawk and SimWB. 
CS-DD-67106K-400R DDC BU-67106K-400R-JLO PCI Express (x1) MIL-STD-1553 device. Four dual redundantMIL-STD-1553 channels operating modes are BC/Monitor or Multi-RT/Monitor.The card also contains software configurable bus coupling and termination options, eight digital discrete I/Os, eight avionics (+35V) Discrete I/Os, IRIG-B Time Code Input/Output, and a Time Tag Clock Input/Output. Commercial Temp. (This 1553 device is supported with SWB - License ICS-SWB-225 is required). Supported by RedHawk and SimWB. 
CS-DD-67206K-100R DDC BU-67206K-100R-JLO (Multi-Function) PCI Express (x1) MIL-STD-1553 device. Single dual redundant MIL-STD-1553 channels. Multi-Function: BC + Multi-RT + Monitor. Enhanced features, Onboard DMA Engine, Bridgeless PCIe Design, MIS Interrupts. PCIe x1 form factor. Test and Simulation Toolkit: Error Injection, Variable Voltage Output, Advanced Triggering. The card also contains software configurable bus coupling and termination options, eight digital discrete I/Os, eight avionics (+35V) Discrete I/Os, IRIG-B Time Code Input/Output, and a Time Tag Clock Input/Output. Commercial Temp. (This 1553 device is supported with SWB - RIQ Required). Supported by RedHawk and SimWB. 
CS-DD-67206K-200R DDC BU-67206K-200R-JLO (Multi-Function) PCI Express (x1) MIL-STD-1553 device. Two dual redundant MIL-STD-1553 channels. Multi-Function: BC + Multi-RT + Monitor. Enhanced features, Onboard DMA Engine, Bridgeless PCIe Design, MIS Interrupts. PCIe x1 form factor. Test and Simulation Toolkit: Error Injection, Variable Voltage Output, Advanced Triggering. The card also contains software configurable bus coupling and termination options, eight digital discrete I/Os, eight avionics (+35V) Discrete I/Os, IRIG-B Time Code Input/Output, and a Time Tag Clock Input/Output. Commercial Temp. (This 1553 device is supported with SWB - RIQ Required). Supported by RedHawk and SimWB. 
CS-DD-67206K-400R DDC BU-67206K-400R-JLO (Multi-Function) PCI Express (x1) MIL-STD-1553 device. Four dual redundant MIL-STD-1553 channels. Multi-Function: BC + Multi-RT + Monitor. Enhanced features, Onboard DMA Engine, Bridgeless PCIe Design, MIS Interrupts. PCIe x1 form factor. Test and Simulation Toolkit: Error Injection, Variable Voltage Output, Advanced Triggering. The card also contains software configurable bus coupling and termination options, eight digital discrete I/Os, eight avionics (+35V) Discrete I/Os, IRIG-B Time Code Input/Output, and a Time Tag Clock Input/Output. Commercial Temp. (This 1553 device is supported with SWB - RIQ Required). Supported by RedHawk and SimWB. 
CS-DD-D42916I3 (PMC) 16 independent programmable receiver/transmitter, high/low speed ARINC channels with receive label/SDI data filtering and data time stamping; on-board processor for engineering unit conversions and data processing, dual-port RAM. Requires an available PMC position. (DDC p/n . DD-42916C1-300 ) Supported by RedHawk and SimWB. 
       Elektrobit FlexRay
CS-EB-5100 EB 5100: Active FlexRay Interface Hardware for PCI - High performance Freescale MPC5200B Microcontroller with 400Mhz 32MB SDRAM / 8MB Flash - 5 slots for physical layer modules - 2 FlexRay E-Ray Controllers in FPGA. Requires Configuration Tool EB tresos Busmirror - Requires previous purchase of EB tresos Busmirror Configuraiton tools via the RIQ process. This item is included in this catalog for repeat board purchase only. Available for 32-bit systems only at this time. Cannot be purchased for 64-bit systems. 
       ESD Electronics CANbus
CS-ES-CAN-400-2E ESD CAN-PCIe/400-2 The CAN-PCIe/400 is a PC board designed for the PCI Express bus that features two CAN High-Speed interfaces acc. to ISO 11898-2. (p/n C.2043.04) Available for 32-bit systems and 64-bit systems. 
CS-ES-CAN-400-4E ESD CAN-PCIe/400-4 The CAN-PCIe/400 is a PC board designed for the PCI Express bus that features four (CAN-PCIe/400-4) CAN High-Speed interfaces acc. to ISO 11898-2. CAN-PCIe/400-4 comes with two CAN interfaces via a separate slot bracket. Two Rear I/O positions are required to accommodate channels 3 and 4. (p/n C.2043.06) Available for 32-bit systems and 64-bit systems. 
CS-ES-CAN-400-4M ESD CAN-PMC/400 4-channel CAN Bus device The PMC-CAN/400-4 features four electrically isolated CAN High-Speed interfaces according to ISO 11898. A FPGA handles the local data control and management. The PMC-CAN/400-4 provides high-resolution hardware timestamps. (C.2407.03 & C.1101.02) Available for 32-bit systems and 64-bit systems. 
CS-ES-CAN-405-2 OBSOLETE MODEL NUMBER - USE CS-ES-CAN-405-2P Available for 32-bit systems and 64-bit systems. 
CS-ES-CAN-405-2P ESD CAN-PCI/405 2-channel CAN Bus device w/ IBM PPC405GP, 200MHz, 32MB SDRAM, 4MB Flash 4x CAN w/ Paddle Card adapter. Available for 32-bit systems and 64-bit systems. 
CS-ES-CAN-405-4 OBSOLETE MODEL NUMBER - USE CS-ES-CAN-405-4P Available for 32-bit systems and 64-bit systems. 
CS-ES-CAN-405-4P ESD CAN-PCI/405 4-channel CAN Bus device w/ IBM PPC405GP, 200MHz, 32MB SDRAM, 4MB Flash 4x CAN w/ Paddle Card adapter. Requires an available PCI Slot and PCI opening for channels 3 & 4. Available for 32-bit systems and 64-bit systems. 
CS-ES-CAN-PMC400-4 OBSOLETE MODEL NUMBER - USE CS-ES-CAN-400-4M Available for 32-bit systems and 64-bit systems. 
       GE Intelligent Platforms Reflective Memory and Ethernet
CS-GE-CBL-F6-002 10 Foot (3.048 m) Multimode Duplex LC Fiber-optic Cable. (GE-IP p/n CBL-000-F6-002) - This Duplex Cable is Ideal for a 2 Node network. For a 3+ node network, it is best to use simplex cables. (See CS-VMIC-CBL-F5-00X).  
CS-GE-CBL-F6-003 16 feet (4.8768 m) Multimode Duplex LC Fiber-optic Cable. (GE-IP p/n CBL-000-F6-003) - This Duplex Cable is Ideal for a 2 Node network. For a 3+ node network, it is best to use simplex cables. (See CS-VMIC-CBL-F5-00X).  
CS-GE-CBL-F6-004 32 feet (9.7536 m) Multimode Duplex LC Fiber-optic Cable. (GE-IP p/n CBL-000-F6-004) - This Duplex Cable is Ideal for a 2 Node network. For a 3+ node network, it is best to use simplex cables. (See CS-VMIC-CBL-F5-00X).  
CS-GE-PCE-5565-100 GE PCIe-5565PIORC-100A00 -PCI Express, 2 GIGA Baud RM w/FO Options, 128 Mbyte Memory, Multimode Transmission. Short bracket option (low profile) configuration of this card is available upon request. (Replaces CS-VMIPCE-5565-100) Supported by RedHawk and SimWB. 
CS-GE-PCE-5565-200 GE PCIe-5565PIORC-200A00 -PCI Express, 2 GIGA Baud RM w/FO Options, 256 Mbyte Memory, Multimode Transmission. Short bracket option (low profile) configuration of this card is available upon request. (Replaces CS-VMIPCE-5565-200) Supported by RedHawk and SimWB. 
CS-GE-PCI-5565-110 GE PCI-5565PIORC-110000 - PCI 128 MB Fiber-Optic Reflective Memory w/4Kb FIFO/Multimode. (Replaces CS-VMIPCI-5565-010) Supported by RedHawk and SimWB. 
CS-GE-PCI-5565-210 PCI-5565PIORC-210000 - PCI 256 MB Fiber-Optic Reflective Memory w/4Kb FIFO/Multimode. (Replaces CS-VMIPCI-5565-020) Supported by RedHawk and SimWB. 
CS-GE-PMC-5565-110 GE PMC-5565PIORC-110000 - PMC 128 MB Fiber-Optic Reflective Memory w/4Kb FIFO/Multimode. Supported by RedHawk and SimWB. 
CS-GE-PMC-5565-111 GE PMC-5565PIORC-111000 - PMC 128 MB Fiber-Optic Reflective Memory w/4Kb FIFO/Single Mode. (NOTE: This item has an extended lead time of 16 Weeks) Supported by RedHawk and SimWB. 
CS-GE-PMC677RCTX PMC677RCTX is a Quad-Port Ethernet PMC device. Support 10/100/1000BaseT, 64KB FIFO Buffers. RoHS Compliant, 3.3V Signaling, Pluggable copper transceivers, PCI-X/PCI 64bit/66Mhz bus compatible. Driver is included with RedHawk Server Linux 
       General Standards Data Acquistion
CS-GS-16AI64LL-2 PCI 16-Bit - 32(Diff)/64(SE) Ch. A/D; Customized version of the GS-16AI64 device to provide Low-Latency analog input. Single ADC per Board, therefore 500k Conversions per second is only obtainable when sampling a single channel. This board is optimized for Hardware-in-the-Loop applications and not pure data aquisition. This is a PMC adapter mounted on a PCI carrier. GS P/N PCI-16AI64LL-2 Supported by RedHawk and SimWB. 
CS-GS-16AI64LL-2-E PCIe 16-Bit - 32(Diff)/64(SE) Ch. A/D; Customized version of the GS-16AI64 device to provide Low-Latency analog input. Single ADC per Board, therefore 500k Conversions per second is only obtainable when sampling a single channel. This board is optimized for Hardware-in-the-Loop applications and not pure data aquisition. This is a PMC adapter mounted on a PCIe carrier. GS P/N PCIe-16AI64LL-2 Supported by RedHawk and SimWB. 
CS-GS-16AI64SSA-2 **NOT RECOMMENDED FOR NEW DESIGNS ** PCI-16AI64SSA-64-256K is an older design - See CS-GS-16AI64SSC for replacement) - 16-Bit - 32(Diff)/64(SE) Ch. A/D 200KSPS 16-bit ADC per Channel, Simultaneous Sampling of all inputs, D32/D64 Universal PCI, Bi-polar/Uni Polar 2.5V, 5V & 10V - with PCI carrier. Supported by RedHawk and SimWB. 
CS-GS-16AI64SSC PCI66-16AI64SSC-64-50M - PCI-X Device 16-Bit - 32(Diff)/64(SE) Ch. A/D 200KSPS 16-bit ADC per Channel, 50.000M Clock Frequency, Simultaneous Sampling of all inputs, D32/D64 Universal PCI, Bi-polar/Uni Polar 2.5V, 5V & 10V - This card is PMC device on a PCI-X carrier. GS P/N PCI66-16AI64SSC-64-50M Supported by RedHawk and SimWB. 
CS-GS-16AI64SSC-E PCIe-16AI64SSC-64-50M-0-0 - PCIE Device 16-Bit - 32(Diff)/64(SE) Ch. A/D 200KSPS 16-bit ADC per Channel, Simultaneous Sampling of all inputs, D32/D64, Bi-polar/Uni Polar 2.5V, 5V & 10V, Clock Freq. 50.000M - This card is a true PCIe x1 form-factor. GS P/N PCIe-16AI64SSC-64-50M-0-0 Supported by RedHawk and SimWB. 
CS-GS-16AI64SSC-EL PCIe-16AI64SSC-64-50M-0-LL (Low Latency) - PCIE Device 16-Bit - 32(Diff)/64(SE) Ch. A/D 200KSPS 16-bit ADC per Channel, Simultaneous Sampling of all inputs, D32/D64, Bi-polar/Uni Polar 2.5V, 5V & 10V, Clock Freq. 50.000M - Low Latency - This card is a true PCIe x1 form-factor. GS P/N PCIe-16AI64SSC-64-50M-0-LL Supported by RedHawk and SimWB. 
CS-GS-16AIO-41 16-Bit - 32(SE)/16(D) Ch. A/D; 4Ch. D/A; 16-Bit DIO (General Standards PCI-16AIO-41 - PMC device mounted on PCI carrier) Supported by RedHawk and SimWB. 
CS-GS-16AIO-41E 16-Bit - 32(SE)/16(D) Ch. A/D; 4Ch. D/A; 16-Bit DIO (General Standards PCIe-16AIO-41 - PMC device mounted on PCIe carrier) Supported by RedHawk and SimWB. 
CS-GS-16AIO-PMC-S3 PMC device w/ SCSI3 68-pin connectors: 16-Bit - 32(SE)/16(D) Ch. A/D; 4Ch. D/A; 16-Bit DIO (General Standards True PMC device PMC-16AIO-41-SCSI3.) Supported by RedHawk and SimWB. 
CS-GS-16AO12-10201 (End-of-Life - Use CS-GS-16AO16) 16-Bit - +-5V output range, no output filter, 12 D/A outputs, 400KSPS each channel, 32K deep FIFO buffer, and Non-differential Sync I/O This product has reached End-of-Life. Please see CS-GS-16AO16 for FFF replacement. 
CS-GS-16AO12-10202 (End-of-Life - Use CS-GS-16AO16)16-Bit - +-5V output range, no output filter, 12 D/A outputs, 400KSPS each channel, 32K deep FIFO buffer, and differential Sync I/O (with R402 installed) This product has reached End-of-Life. Please see CS-GS-16AO16 for FFF replacement. 
CS-GS-16AO12-20201 (End-of-Life - Use CS-GS-16AO16) 16-Bit - +-10V output range, no output filter, 12 D/A outputs, 400KSPS each channel, 32K deep FIFO buffer, and non-differential Sync I/O This product has reached End-of-Life. Please see CS-GS-16AO16 for FFF replacement. 
CS-GS-16AO12-20202 (End-of-Life - Use CS-GS-16AO16) 16-Bit - +-10V output range, no output filter, 12 D/A outputs, 400KSPS each channel, 32K deep FIFO buffer, and differential Sync I/O (with R402 installed) This product has reached End-of-Life. Please see CS-GS-16AO16 for FFF replacement. 
CS-GS-16AO16-0811 8-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support, No Output Filters, Differential Outputs (GS p/n PCI66-16AO16-8-F0-DF) Supported by RedHawk and SimWB. 
CS-GS-16AO16-0812 8-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support, No Output Filters, Single Ended Outputs (GS p/n PCI66-16AO16-8-F0-SE) Supported by RedHawk and SimWB. 
CS-GS-16AO16-0821 8-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support, 10kHz Output Filters, Differential Outputs (GS p/n PCI66-16AO16-8-F10-DF) Supported by RedHawk and SimWB. 
CS-GS-16AO16-0822 8-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support, 10kHz Output Filters, Single Ended Outputs (GS p/n PCI66-16AO16-8-F10-SE) Supported by RedHawk and SimWB. 
CS-GS-16AO16-0831 8-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support, 100kHz Output Filters, Differential Outputs (GS p/n PCI66-16AO16-8-F100-DF) Supported by RedHawk and SimWB. 
CS-GS-16AO16-0832 8-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support, 100kHz Output Filters, Single Ended Outputs (GS p/n PCI66-16AO16-8-F100-SE) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1211 12-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support No Output Filters, Differential Outputs (GS p/n PCI66-16AO16-12-F0-DF) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1212 12-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support No Output Filters, Single Ended Outputs (GS p/n PCI66-16AO16-12-F0-SE) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1221 12-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support 10kHz Output Filters, Differential Outputs (GS p/n PCI66-16AO16-12-F10-DF) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1222 12-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support 10kHz Output Filters, Single Ended Outputs (GS p/n PCI66-16AO16-12-F10-SE) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1231 12-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support 100kHz Output Filters, Differential Outputs (GS p/n PCI66-16AO16-12-F100-DF) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1232 12-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support 100kHz Output Filters, Single Ended Outputs (GS p/n PCI66-16AO16-12-F100-SE) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1611 16-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support No Output Filters, Differential Outputs (GS p/n PCI66-16AO16-16-F0-DF) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1611E 16-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCIe - No Output Filters, Differential Outputs (GS p/n PCIe-16AO16-16-F0-DF) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1612 16-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support No Output Filters, Single Ended Outputs (GS p/n PCI66-16AO16-16-F0-SE) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1612E 16-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCIe - No Output Filters, Single Ended Outputs (GS p/n PCIe-16AO16-16-F0-SE) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1621 16-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support 10kHz Output Filters, Differential Outputs (GS p/n PCI66-16AO16-16-F10-DF) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1621E 16-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCIe - 10kHz Output Filters, Differential Outputs (GS p/n PCIe-16AO16-16-F10-DF) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1622 16-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support 10kHz Output Filters, Single Ended Outputs (GS p/n PCI66-16AO16-16-F10-SE) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1622E 16-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCIe -10kHz Output Filters, Single Ended Outputs (GS p/n PCIe-16AO16-16-F10-SE) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1631 16-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support 100kHz Output Filters, Differential Outputs (GS p/n PCI66-16AO16-16-F100-DF) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1631E 16-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCIe - 100kHz Output Filters, Differential Outputs (GS p/n PCIe-16AO16-16-F100-DF) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1632 16-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCI 66MHz Support 100kHz Output Filters, Single Ended Outputs (GS p/n PCI66-16AO16-16-F100-SE) Supported by RedHawk and SimWB. 
CS-GS-16AO16-1632E 16-Channel 16-Bit High-Speed Analog Output Board w/ 400,000 Samples per Second per Channel, and Simultaneous Clocking - PCIe - 100kHz Output Filters, Single Ended Outputs (GS p/n PCIe-16AO16-16-F100-SE) Supported by RedHawk and SimWB. 
CS-GS-16AO16-WAVE The Concurrent Computer Corporation CS-GS-16AO16-WAVE package consists of a library and test program that interface with the WCS-GS-16AO16 driver to provide an easy, yet powerful mechanism for users to generate continuous and unique user-supplied waveforms on any specified channels for GSC-16AO16 cards. The WCS-GS-16AO16 driver or WCS-GS-66-16AO16 driver is a pre-requisite. The WCS-GS-16AO16 driver or WCS-GS-66-16AO16 driver is a pre-requisite to purchase of this WAVE Software Product. 
CS-GS-16AO64-32DBE 32-Channels Differential, 16-Bit High-Speed Analog Output Board w/ 500,000 samples per second per channel. Bi-Polar 10V, 5V, or 0-5V, No Filters, Output Disconnect. PCIe x1 adapter. (GS p/n PCIe-16AO64C-32D-BP-F1-49.152M-OD-0) Not supported by SWB at this time. RIQ required if SWB support is needed. 
CS-GS-16AO64-32SBE 32-Channels Single Ended 16-Bit High-Speed Analog Output Board w/ 500,000 samples per second per channel. Bi-Polar 10V, 5V, or 0-5V, No Filters, Output Disconnect. PCIe x1 adapter. (GS p/n PCIe-16AO64C-32S-BP-F1-49.152M-OD-0) Not supported by SWB at this time. RIQ required if SWB support is needed. 
CS-GS-16AO64-64SBE 64-Channels Single Ended, 16-Bit High-Speed Analog Output Board w/ 500,000 samples per second per channel. Bi-Polar 10V, 5V, or 0-5V, No Filters, Output Disconnect. PCIe x1 adapter. (GS p/n PCIe-16AO64C-64S-BP-F1-49.152M-OD-0) Not supported by SWB at this time. RIQ required if SWB support is needed. 
CS-GS-16SDI-04 16-Bit - 4Ch A/D (220KSPS Each Channel) Robinson Nugent 68P Conn  
CS-GS-16SDI-08 16-Bit - 8Ch A/D (220KSPS Each Channel) Robinson Nugent 68P Conn  
CS-GS-16SDI-16 16-Bit - 16Ch A/D (220KSPS Each Channel) Robinson Nugent 68P Conn  
CS-GS-24DSI12-4-SF 4-channel, Lowpass Filter Frequencies: Standard 40kHz and 270kHz, PLL Rate Generator)l (General Standards P/N - PCI-24DSI12-4-SF-S-PLL)  
CS-GS-24DSI12-8-SF 8-channel, Lowpass Filter Frequencies: Standard 40kHz and 270kHz, PLL Rate Generator)l (General Standards P/N - PCI-24DSI12-8-SF-S-PLL)  
CS-GS-24DSI12-SF 12-channel, Lowpass Filter Frequencies: Standard 40kHz and 270kHz, PLL Rate Generator)l (General Standards P/N - PCI-24DSI12-12-SF-S-PLL)  
CS-GS-24DSI32-SD 32-Channel 24-Bit Delta-Sigma PCI Analog Input Board With 200 KSPS Sample Rate per Channel, Standard Low Distortion, Image Filter Standard 40kHz and 270kHz, PLL Rate Generator (General Standards P/N - PCI-24DSI32-32-SD-0-PL25)  
CS-GS-66-16AI64SSA **OBSOLETE - NOT RECOMMENDED FOR NEW DESIGNS ** PCI66-16AI64SSA-64-B is an older design - See CS-GS-16AI64SSC for replacement) - - 16-Bit - 32(Diff)/64(SE) Ch. A/D 200KSPS 16-bit ADC per Channel, Simultaneous Sampling of all inputs, D32/D64 66MHz Universal PCI, Bi-polar/Uni Polar 2.5V, 5V & 10V - with PCI carrier. (GS P/N PCI66-16AI64SSA-64-B) **NOT RECOMMENDED FOR NEW DESIGNS ** PCI66-16AI64SSA-64-B is an older design - See CS-GS-16AI64SSC for replacement) -  
CS-GS-66-16AI8AO0 PCI66-16AISS8AO4-8-0 -40.32M 16-Bit, 12-Channel, 2-MSPS PCI Analog Input/Output Board With Eight Simultaneously Sampled Analog Inputs, Zero (0) Analog Outputs, Input Sampling Rates to 2.0 MSPS per channel. (Note - General Standards does not provide a cost break for this device without the Analog Output Channels at this time)  
CS-GS-66-16AI8AO4 PCI66-16AISS8AO4-8-4 -40.32M 16-Bit, 12-Channel, 2-MSPS PCI Analog Input/Output Board With Eight Simultaneously Sampled Analog Inputs, Four Analog Outputs, Input Sampling Rates to 2.0 MSPS per channel, and Simultaneous Output Clocking Rates to 1.0 MSPS per Channel  
CS-GS-66-16AO081CD PCI66-16AO16-FLV-08-F1-HC-S Analog Output: +-(2.5,1.5) V High Current output range, 8 single-ended output channels (2 wire), 256K FIFO buffer, software selectable Elliptic output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO081LD PCI66-16AO16-FLV-08-F1-HL-D Analog Output: +-(5, 10) V High Level output range, 8 Channel Differential (3-wire), 256K FIFO buffer, software selectable Elliptic output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO082CD PCI66-16AO16-FLV-08-F2-HC-S Analog Output: +-(2.5,1.5) V High Current output range, 8 single-ended output channels (2 wire), 256K FIFO buffer, software selectable Butterworth output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO082LD PCI66-16AO16-FLV-08-F2-HL-D Analog Output: +-(5, 10) V High Level output range, 8 Channel Differential (3-wire), 256K FIFO buffer, software selectable Butterworth output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO083CD PCI66-16AO16-FLV-08-F3-HC-S Analog Output: +-(2.5,1.5) V High Current output range, 8 single-ended output channels (2 wire), 256K FIFO buffer, software selectable Elliptic output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO083LD PCI66-16AO16-FLV-08-F3-HL-D Analog Output: +-(5, 10) V High Level output range, 8 Channel Differential (3-wire), 256K FIFO buffer, software selectable Elliptic output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO121CS PCI66-16AO16-FLV-12-F1-HC-S Analog Output: +-(2.5,1.5) V High Current output range, 12 single-ended output channels (2 wire), 256K FIFO buffer, software selectable Elliptic output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO121LD PCI66-16AO16-FLV-12-F1-HL-D Analog Output: +-(5, 10) V High Level output range, 12 Channel Differential (3-wire), 256K FIFO buffer, software selectable Elliptic output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO122CS PCI66-16AO16-FLV-12-F2-HC-S Analog Output: +-(2.5,1.5) V High Current output range, 12 single-ended output channels (2 wire), 256K FIFO buffer, software selectable Butterworth output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO122LD PCI66-16AO16-FLV-12-F2-HL-D Analog Output: +-(5, 10) V High Level output range, 12 Channel Differential (3-wire), 256K FIFO buffer, software selectable Butterworth output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO123CS PCI66-16AO16-FLV-12-F3-HC-S Analog Output: +-(2.5,1.5) V High Current output range, 12 single-ended output channels (2 wire), 256K FIFO buffer, software selectable Elliptic output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO123LD PCI66-16AO16-FLV-12-F3-HL-D Analog Output: +-(5, 10) V High Level output range, 12 Channel Differential (3-wire), 256K FIFO buffer, software selectable Elliptic output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO161CS PCI66-16AO16-FLV-16-F1-HC-S Analog Output: +-(2.5,1.5) V High Current output range, 16 single-ended output channels (2 wire), 256K FIFO buffer, software selectable Elliptic output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO161LD PCI66-16AO16-FLV-16-F1-HL-D Analog Output: +-(5, 10) V High Level output range, 16 Channel Differential (3-wire), 256K FIFO buffer, software selectable Elliptic output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO161LS PCI66-16AO16-FLV-16-F1-HL-S Analog Output: +-(5, 10) V High Level output range, 16 Channel Single ended (2-wire), 256K FIFO buffer, software selectable Elliptic output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO162CS PCI66-16AO16-FLV-16-F2-HC-S Analog Output: +-(2.5,1.5) V High Current output range, 16 single-ended output channels (2 wire), 256K FIFO buffer, software selectable Butterworth output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO162LD PCI66-16AO16-FLV-16-F2-HL-D Analog Output: +-(5, 10) V High Level output range, 16 Channel Differential (3-wire), 256K FIFO buffer, software selectable Butterworth output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO163CS PCI66-16AO16-FLV-16-F3-HC-S Analog Output: +-(2.5,1.5) V High Current output range, 16 single-ended output channels (2 wire), 256K FIFO buffer, software selectable Elliptic output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-66-16AO163LD PCI66-16AO16-FLV-16-F3-HL-D Analog Output: +-(5, 10) V High Level output range, 16 Channel Differential (3-wire), 256K FIFO buffer, software selectable Elliptic output filter, 33/66MHz PCI interface, 5PPM precision oscillator;  
CS-GS-ADADIO-232 PCI Form Factor - 16-Bit - +/- 5V 8 Ch. A/D, 4Ch. D/A, 4KHz Output Filter , 8-bit DIO (200Khz) (May be delivered as a PMC device on a PCI/PMC Carrier by General Standards)  
CS-GS-ADADIO-311 PCI Form Factor - 16-Bit - +/-10V 8 Ch. A/D, 4Ch. D/A, No Output Filter , 8-bit DIO (100Khz) (May be delivered as a PMC device on a PCI/PMC Carrier by General Standards)  
CS-GS-ADADIO-31164 PCI66 Version - 16-Bit - 8 Ch. A/D, 4Ch. D/A, 8-bit DIO (100Khz)  
CS-GS-ADADIO-312 PCI Form Factor - 16-Bit - +/- 10V 8 Ch. A/D; 4Ch. D/A, No Output Filter; 8-bit DIO (200Khz) (May be delivered as a PMC device on a PCI/PMC Carrier by General Standards)  
CS-GS-ADADIO-31264 PCI66 Version - 16-Bit - 8 Ch. A/D, 4Ch. D/A, 8-bit DIO (200Khz)  
CS-GS-BOX-B64SS-64 64 BNC Rackmount BOX for PCI/PCIe 16AI64SSX devices - General Standards p/n BOX-BNC-PCI66-16AI64SSA-64 This panel will work with both the CS-GS-16AI64SSA and CS-GS-16AI64SSC family of analog input adpaters. 
CS-GS-C06-DIO24 6 foot Cable Non-Shielded for the CS-GS-DIO24 (CBL6-DIO24)  
CS-GS-C06-HPDI32 6 foot Cable Non-Shielded for the CS-GS-HPDI32x Series (CBL6-HPDI32)  
CS-GS-C06-OPT32 6 foot Cable Non-Shielded for the CS-GS-OPTO32Ax (CBL6-OPTO32A)  
CS-GS-C06-PCIe-PMC 6 foot Cable Non-Shielded for the for the PCIe1-PCM Adapter. Used to support PMC devices with Rear I/O that are mounted on a PCIe1-to-PMC Adapter. This cable has a 68 pin Robinson Nugent connector on both ends. GS p/n CBL6-PCIe1-PMC.  
CS-GS-C12-DIO24 12 foot Cable Non-Shielded for the CS-GS-DIO24 (CBL12-DIO24)  
CS-GS-C12-HPDI32 12 foot Cable Non-Shielded for the CS-GS-HPDI32ALx Series (CBL12-HPDI32)  
CS-GS-C12-OPT32 12 foot Cable Non-Shielded for the CS-GS-OPTO32Ax (CBL12-OPTO32A)  
CS-GS-C12-SIO4B-S3 12 foot Cable Non-Shielded w/ DB25 (Female) Connectors for the CS-GS-SIO4B-A4-64 Sync Serial Controler (CABLE12-SIO4B-STD3-DB25S)  
CS-GS-C12-SIO8BX 12 foot Cable Non-Shielded w/ DB25 (Female) Connectors for the CS-GS-SIO8BXa-0 Sync Serial Controler (CBL12-SIO8XA-STD3-DB25S)  
CS-GS-C12-SIO8BX2 12 foot Cable Non-Shielded w/ DB25 (Female) Connectors for the CS-GS-SIO8BX2 Sync Serial Controler (GS p/n CBL12-PCIe-SIO8BX2-DB25S-RS530A)  
CS-GS-C15-SIO4B 1.5 foot Cable Non-Shielded w/ DB25 (Female) Connectors for the CS-GS-SIO4B-A4x Sync Serial Controller (CBL1.5-SIO4B-STD3-DB25S)  
CS-GS-C15-SIO4BX 1.5 foot Cable Non-Shielded w/ DB25 (Female) Connectors for the CS-GS-SIO4BXx Sync Serial Controller (CBL1.5-SIO4B-STD3-DB25S)  
CS-GS-C3-16AO-B08 3 foot Cable w/ 8 BNC Connectors for the CS-GS-16AOx (x=12 or 16) devices (CABLE3-PCI-16AO16-XX-BNC-08) (XX = Differential or Single Ended must be specified at time of purchase or order the specific cable from below.  
CS-GS-C3-16AO-B08D 3 foot Cable w/ 8 BNC Connectors for the CS-GS-16AOx (x=12 or 16) Differential device configurations (CABLE3-PCI-16AO16-DF-BNC-08)  
CS-GS-C3-16AO-B08S 3 foot Cable w/ 8 BNC Connectors for the CS-GS-16AOx (x=12 or 16) Single Ended device configurations (CABLE3-PCI-16AO16-SE-BNC-08)  
CS-GS-C3-16AO-B12D 3 foot Cable w/ 12BNC Connectors for the CS-GS-16AOx (x=12 or 16) Differential device configurations (CABLE3-PCI-16AO16-DF-BNC-12)  
CS-GS-C3-16AO-B12S 3 foot Cable w/ 12 BNC Connectors for the CS-GS-16AOx (x=12 or 16) Single Ended device configurations (CABLE3-PCI-16AO16-SE-BNC-12)  
CS-GS-C3-16AO-B16D 3 foot Cable w/ 16 BNC Connectors for the CS-GS-16AOx (x=12 or 16) Differential device configurations (CABLE3-PCI-16AO16-DF-BNC-16)  
CS-GS-C3-16AO-B16S 3 foot Cable w/ 16 BNC Connectors for the CS-GS-16AOx (x=12 or 16) Single Ended device configurations (CABLE3-PCI-16AO16-SE-BNC-16)  
CS-GS-C3-64SS-B16D 3 foot Cable w/ 32 BNC Connectors for the CS-GS-16AI64SSA-2 and CS-GS-16AI64SSCx adapters. (CABLE03-PCI-16AI64SSC-DF-BNC-32) Differential Cable This cable is valid with both 64SSA and 64SSC versions of analog input device adapters. 
CS-GS-C3-64SS-B16S 3 foot Cable w/ 16 BNC Connectors for the CS-GS-16AI64SSA-2 and CS-GS-16AI64SSCx adapters. (CABLE03-PCI-16AI64SSC-SE-BNC-16) Single Ended Cable This cable is valid with both 64SSA and 64SSC versions of analog input device adapters. 
CS-GS-C3-64SS-B32D 3 foot Cable w/ 64 BNC Connectors for the CS-GS-16AI64SSA-2 and CS-GS-16AI64SSCx adapters. (CABLE03-PCI-16AI64SSC-DF-BNC-64) Differential Cable This cable is valid with both 64SSA and 64SSC versions of analog input device adapters. 
CS-GS-C3-64SS-B32S 3 foot Cable w/ 32 BNC Connectors for the CS-GS-16AI64SSA-2 and CS-GS-16AI64SSCx adapters. (CABLE03-PCI-16AI64SSC-SE-BNC-32) Single Ended Cable This cable is valid with both 64SSA and 64SSC versions of analog input device adapters. 
CS-GS-C3-64SS-B64S 3 foot Cable w/ 64 BNC Connectors for the CS-GS-16AI64SSA-2 and CS-GS-16AI64SSCx adapters. (CABLE03-PCI-16AI64SSC-SE-BNC-64) Single Ended Cable This cable is valid with both 64SSA and 64SSC versions of analog input device adapters. 
CS-GS-C3-SIO4BX25P 3 foot Cable Non-Shielded w/ DB25 Male Connectors for the CS-GS-SIO4BXx Sync Serial Controller (GS p/n: CABLE3-SIO4B-STD3-DB25P)  
CS-GS-C3-SIO4BX25S 3 foot Cable Non-Shielded w/ DB25 Female Connectors for the CS-GS-SIO4BXx Sync Serial Controller (GS p/n: CABLE3-SIO4B-STD3-DB25S)  
CS-GS-C6-OPTO32A Custom PCI-OPTO32 6.5 foot Cable for the CS-GS-OPTO32Ax board (Ribbon cable with a 68pin SCSI D-bub and DB25F and 3 DB25M) (Vendor p/n CABLE6.5-OPTO32A-3DB25M-2DB25F) This cable is a non-standard cable from General Standards: CABLE6.5-OPTO32A-3DB25M-2DB25F  
CS-GS-C75-SIO8BXS 7.5 foot Cable Non-Shielded w/ DB25 Female Connectors, RS530A Pinout for the CS-GS-SIO8BXx Serial Controler (CBL7.5-SIO8BXS-DB25S-RS530A )  
CS-GS-C9-16AIO-B04 9 foot Cable w/ 4 BNC Connectors for the CS-GS-16AIOx (CABLE3-PCI-16AIO-XX-BNC-4) XX = Must Specify Single Ended or Differential at time of purchase.  
CS-GS-C9-16AO-B08D 9 foot Cable w/ 8 BNC Connectors for the CS-GS-16AOx (x=12 or 16) (CABLE3-PCI-16AO16-DF-BNC-08) Differential Cable  
CS-GS-C9-16AO-B08S 9 foot Cable w/ 8 BNC Connectors for the CS-GS-16AOx (x=12 or 16) (CABLE3-PCI-16AO16-SE-BNC-08) Single Ended Cable  
CS-GS-C9-16AO-B12D 9 foot Cable w/ 12 BNC Connectors for the CS-GS-16AOx (x=12 or 16) (CABLE3-PCI-16AO16-DF-BNC-12) Differential Cable  
CS-GS-C9-16AO-B12S 9 foot Cable w/ 12 BNC Connectors for the CS-GS-16AOx (x=12 or 16) (CABLE3-PCI-16AO16-SE-BNC-12) Single Ended Cable  
CS-GS-C9-16AO-B16D 9 foot Cable w/ 16 BNC Connectors for the CS-GS-16AOx (x=12 or 16) (CABLE3-PCI-16AO16-DF-BNC-16) Differential Cable  
CS-GS-C9-16AO-B16S 9 foot Cable w/ 16 BNC Connectors for the CS-GS-16AOx (x=12 or 16) (CABLE3-PCI-16AO16-SE-BNC-16) Single Ended Cable  
CS-GS-C9-64SS-B16D 9 foot Cable w/ 16 BNC Connectors for the CS-GS-16AI64SSC (CABLE09-PCI-16AI64SSC-DF-BNC-16) Differential Cable  
CS-GS-C9-64SS-B16S 9 foot Cable w/ 16 BNC Connectors for the CS-GS-16AI64SSC (CABLE09-PCI-16AI64SSC-SE-BNC-16) Single Ended Cable  
CS-GS-C9-64SS-B32D 9 foot Cable w/ 32 BNC Connectors for the CS-GS-16AI64SSC (CABLE09-PCI-16AI64SSC-DF-BNC-32) Differential Cable  
CS-GS-C9-64SS-B32S 9 foot Cable w/ 32 BNC Connectors for the CS-GS-16AI64SSC (CABLE09-PCI-16AI64SSC-SE-BNC-32) Single Ended Cable  
CS-GS-C9-64SSA-B16 9 foot Cable w/ 16 BNC Connectors for the CS-GS-16AI64SSx (x=A or C) (CABLE09-PCI-16AI64SSA-XX-BNC-16) XX = Must Specify Single Ended or Differential at time of purchase.  
CS-GS-C9-64SSA-B32 9 foot Cable w/ 32 BNC Connectors for the CS-GS-16AI64SSx (x=A or C) (CABLE09-PCI-16AI64SSA-XX-BNC-32) XX = Must Specify Single Ended or Differential at time of purchase.  
CS-GS-C9-SIO4BX25P 9 foot Cable Non-Shielded w/ DB25 Male Connectors for the CS-GS-SIO4BXx Sync Serial Controller (GS p/n: CABLE9-SIO4B-STD3-DB25P)  
CS-GS-C9-SIO4BX25S 9 foot Cable Non-Shielded w/ DB25 Female Connectors for the CS-GS-SIO4BXx Sync Serial Controller (GS p/n: CABLE9-SIO4B-STD3-DB25S)  
CS-GS-CS6-16A0643D 6 foot Cable Shielded for the CS-GS-16AO64-32DBE 32 Channel, 16 Bit Differential Analog Output adapter ( GS Cable p/n CABLE6-PCIe-16AO64C-32D-BP-F1-49.152M-OD-0)  
CS-GS-CS6-16A0643S 6 foot Cable Shielded for the CS-GS-16AO64-32SBE 32 Channel, 16 Bit Single Ended Analog Output adapter ( GS Cable p/n CABLE6-PCIe-16AO64C-32S-BP-F1-49.152M-OD-0)  
CS-GS-CS6-16A0646S 6 foot Cable Shielded for the CS-GS-16AO64-64SBE 64 Channel, 16 Bit Single Ended Analog Output adapter ( GS Cable p/n CABLE6-PCIe-16AO64C-64S-BP-F1-49.152M-OD-0)  
CS-GS-CSH06-16AI64 6 foot Cable Shielded for the CS-GS-16AI64LLx  
CS-GS-CSH06-16AIO 6 foot Cable Shielded for the CS-GS-16AIOx  
CS-GS-CSH06-16AO 6 foot Cable Shielded for the CS-GS-16AOx and CS-GS-66-16AO16x series cards.  
CS-GS-CSH06-16SDI 6 foot Cable Shielded for the CS-GS-16SDIx  
CS-GS-CSH06-64SSA 6 foot Cable Shielded for the CS-GS-16AI64SSA-2  
CS-GS-CSH06-64SSC 6 foot Cable Shielded for the CS-GS-16AI64SSC  
CS-GS-CSH06-ADIO 6 foot Cable Shielded for the CS-GS-ADADIOx  
CS-GS-CSH09-16AI64 9 foot Cable Shielded for the CS-GS-16AI64LLx  
CS-GS-CSH09-16AIO 9 foot Cable Shielded for the CS-GS-16AIOx  
CS-GS-CSH09-16AO 9 foot Cable Shielded for the CS-GS-16AOx and CS-GS-66-16AO16x series cards.  
CS-GS-CSH09-16SDI 9 foot Cable Shielded for the CS-GS-16SDIx  
CS-GS-CSH09-64SSA 9 foot Cable Shielded for the CS-GS-16AI64SSA-2  
CS-GS-CSH09-64SSC 9 foot Cable Shielded for the CS-GS-16AI64SSC  
CS-GS-CSH09-ADIO 9 foot Cable Shielded for the CS-GS-ADADIOx  
CS-GS-CSH12-16AI64 12 foot Cable Shielded for the CS-GS-16AI64LLx  
CS-GS-CSH12-16AIO 12 foot Cable Shielded for the CS-GS-16AIOx  
CS-GS-CSH12-16AO 12 foot Cable Shielded for the CS-GS-16AOx and CS-GS-66-16AO16x series cards.  
CS-GS-CSH12-16SDI 12 foot Cable Shielded for the CS-GS-16SDIx  
CS-GS-CSH12-64SSA 12 foot Cable Shielded for the CS-GS-16AI64SSA-2  
CS-GS-CSH12-64SSC 12 foot Cable Shielded for the CS-GS-16AI64SSC  
CS-GS-CSH12-ADIO 12 foot Cable Shielded for the CS-GS-ADADIOx  
CS-GS-DIO24 High-Speed Parallel I/O; 24 Input/Output Bits  
CS-GS-HPDI32A-1M High-speed 32 Bit Parallel Digital I/O PCI Board; Differential RS-485/422 cable transceiver version w/ 128K x 32-bit FIFOs on each chan (both Tx & Rx, 1M byte total); GS p/n PCI-HPDI32A-1M  
CS-GS-HPDI32A-256 High-speed 32 Bit Parallel Digital I/O PCI Board; Differential RS-485/422 cable transceiver version w/ 32K x 32-bit FIFOs on each chan (both Tx & Rx, 256K byte total); GS p/n PCI-HPDI32A-256K  
CS-GS-HPDI32A-64 High-speed 32 Bit Parallel Digital I/O PCI Board; Differential RS-485/422 cable transceiver version w/ 8K x 32-bit FIFOs on each chan (both Tx & Rx, 64K byte total);GS P/N PCI-HPDI32A-64K  
CS-GS-HPDI32AE-1M High-speed 32 Bit Parallel Digital I/O PCIe Board; Differential RS-485/422 cable transceiver version w/ 128K x 32-bit FIFOs on each chan (both Tx & Rx, 1M byte total); GS p/n PCIe-HPDI32A-1M  
CS-GS-HPDI32AE-256 High-speed 32 Bit Parallel Digital I/O PCIe Board; Differential RS-485/422 cable transceiver version w/ 32K x 32-bit FIFOs on each chan (both Tx & Rx, 256K byte total); GS p/n PCIe-HPDI32A-256K  
CS-GS-HPDI32AE-64 High-speed 32 Bit Parallel Digital I/O PCIe Board; Differential RS-485/422 cable transceiver version w/ 8K x 32-bit FIFOs on each chan (both Tx & Rx, 64K byte total);GS P/N PCeI-HPDI32A-64K  
CS-GS-HPDI32AL-1M High-speed 32 Bit Parallel Digital I/O PCI Board; Differential RS-485/422 cable transceiver version w/ 128Kx32-bit FIFOs on both Tx & Rx, 1M byte GS p/n PCI64-HPDI32AL-1M-RS485  
CS-GS-HPDI32AL-256 High-speed 32 Bit Parallel Digital I/O PCI Board; 256K Differential RS-485/422 cable transceiver version w/ 32Kx32-bit FIFOs on both Tx & Rx,256K byte total GS p/n PCI64-HPDI32AL-256K-RS485  
CS-GS-HPDI32AL-64 High-speed 32 Bit Parallel Digital I/O PCI Board; 64K Differential RS-485/422 cable transceiver version w/ 8Kx32-bit FIFOs on both Tx & Rx, 64K byte total GS P/N PCI64-HPDI32AL-64K-RS485  
CS-GS-HPDI32AT-1M High-speed 32 Bit Parallel Digital I/O PCI Board; 1M-LVDS with 128Kx32-bit FIFOs on both Tx & Rx, 1M byte total; GS p/n PCI64-HPDI32AL-1M-LVDS  
CS-GS-HPDI32AT-256 High-speed 64 Bit Parallel Digital I/O PCI Board; 256K-LVDS; 32Kx32-bit FIFOs on both Tx & Rx,256K byte total; GS p/n PCI64-HPDI32AL-256K-LVDS  
CS-GS-HPDI32AT-64 High-speed 32 Bit Parallel Digital I/O PCI Board; 64K-LVDS; 8Kx32-bit FIFOs on both Tx & Rx, 64K byte total; GS p/n PCI64-HPDI32AL-64K-LVDS  
CS-GS-HPDI32TL-1M High-speed 32 Bit Parallel Digital I/O PCI Board; 1M-TTL with 128Kx32-bit FIFOs on both Tx & Rx, 1M byte total; GS p/n PCI64-HPDI32ALT-1M-TTL  
CS-GS-HPDI32TL-256 High-speed 32 Bit Parallel Digital I/O PCI Board; 256K-TTL with 32Kx32-bit FIFOs on both Tx & Rx,256K byte total; GS p/n PCI64-HPDI32ALT-256K-TTL  
CS-GS-HPDI32TTL-64 High-speed 32 Bit Parallel Digital I/O PCI Board; 64K-TTL; 8Kx32-bit FIFOs on both Tx & Rx, 64K byte total; GS p/n PCI64-HPDI32ALT-64K-TTL  
CS-GS-IM-16AI64LL Cable Interface Module for the CS-GS-16AI64LL-2. Transitions between high density connectors and high quality spring loaded terminal block. Modules are 2.88 in width (length varies depending on part number) so they can be mounted in standard DIN rail fixtures. Terminal blocks accept 18 - 26 AWG wire.  
CS-GS-IM-16AI64LL1 Cable Interface Module for the CS-GS-16AI64LL-2. Transitions between high density connectors and screw clamp terminal blocks. Modules are 2.88 in width (length varies depending on part number) so they can be mounted in standard DIN rail fixtures. Terminal blocks accept 18 - 26 AWG wire. (Vendor p/n CBLIFMOD-PCI-16AI64LL-1)  
CS-GS-IM-16AI64SS Cable Interface Module for the CS-GS-16AI64SSA & SSC. Transitions between high density connectors and high quality spring loaded terminal blocks. Modules are 2.88 in width (length varies depending on part number) so they can be mounted in standard DIN rail fixtures. Terminal blocks accept 18 - 26 AWG wire.  
CS-GS-IM-16AIO Cable Interface Module for the CS-GS-16AIOx. Transitions between high density connectors and high quality spring loaded terminal blocks. Modules are 2.88 in width (length varies depending on part number) so they can be mounted in standard DIN rail fixtures. Terminal blocks accept 18 - 26 AWG wire.  
CS-GS-IM-16AO12 Cable Interface Module for the CS-GS-16AO12x (Obsolete). Transitions between high density connectors and high quality spring loaded terminal blocks. Modules are 2.88 in width (length varies depending on part number) so they can be mounted in standard DIN rail fixtures. Terminal blocks accept 18 - 26 AWG wire.  
CS-GS-IM-16AO16 Cable Interface Module for the CS-GS-16AO16x and CS-GS-66-16AO16x. Transitions between high density connectors and high quality spring loaded terminal blocks. Modules are 2.88 in width (length varies depending on part number) so they can be mounted in standard DIN rail fixtures. Terminal blocks accept 18 - 26 AWG wire.  
CS-GS-IM-16AO16-I Cable Interface Module for the CS-GS-16AO16x and CS-GS-66-16AO16x. Transitions between high density connectors and screw clamp terminal blocks. Modules are 2.88 in width (length varies depending on part number) so they can be mounted in standard DIN rail fixtures. Terminal blocks accept 18 - 26 AWG wire. (Vendor p/n CBLIFMOD-PCI-16AO16-I)  
CS-GS-IM-16SDI Cable Interface Module for the CS-GS-16SDIx. Transitions between high density connectors and high quality spring loaded terminal blocks. Modules are 2.88 in width (length varies depending on part number) so they can be mounted in standard DIN rail fixtures. Terminal blocks accept 18 - 26 AWG wire.  
CS-GS-IM-24DSI Cable Interface Module for the CS-GS-24DSIx. Transitions between high density connectors and high quality spring loaded terminal blocks. Modules are 2.88 in width (length varies depending on part number) so they can be mounted in standard DIN rail fixtures. Terminal blocks accept 18 - 26 AWG wire.  
CS-GS-IM-ADADIO Cable Interface Module for the CS-GS-ADADIOx. Transitions between high density connectors and high quality spring loaded terminal blocks. Modules are 2.88 in width (length varies depending on part number) so they can be mounted in standard DIN rail fixtures. Terminal blocks accept 18 - 26 AWG wire.  
CS-GS-IM-DIO24 Cable Interface Module for the CS-GS-DIO24. Transitions between high density connectors and high quality spring loaded terminal blocks. Modules are 2.88 in width (length varies depending on part number) so they can be mounted in standard DIN rail fixtures. Terminal blocks accept 18 - 26 AWG wire.  
CS-GS-IM-HPDI32 Cable Interface Module for the CS-GS-HPDI32x. Transitions between high density connectors and high quality spring loaded terminal blocks. Modules are 2.88 in width (length varies depending on part number) so they can be mounted in standard DIN rail fixtures. Terminal blocks accept 18 - 26 AWG wire.  
CS-GS-IM-OPTO32 Cable Interface Module for the CS-GS-OPTO32x. Transitions between high density connectors and high quality spring loaded terminal blocks. Modules are 2.88 in width (length varies depending on part number) so they can be mounted in standard DIN rail fixtures. Terminal blocks accept 18 - 26 AWG wire.  
CS-GS-OPTO32A-05 The CS-PCI-OPTO32A board has 32 optically-coupled digital I/O channels consisting of 8 outputs and 24 inputs. Each channel is electrically isolated (1000 Volts) from the PMC host processor board. Change-of-State Interrupts allow for an interrupt to the PCI host to be generated from any level change on any input. (PCI-OPTO32A-5V)  
CS-GS-OPTO32A-05E The CS-PCIe-OPTO32A board has 32 optically-coupled digital I/O channels consisting of 8 outputs and 24 inputs. Each channel is electrically isolated (1000 Volts) from the PMC host processor board. Change-of-State Interrupts allow for an interrupt to the PCI host to be generated from any level change on any input. (PCIe-OPTO32A-5V)  
CS-GS-OPTO32A-12 The CS-PCI-OPTO32A board has 32 optically-coupled digital I/O channels consisting of 8 outputs and 24 inputs. Each channel is electrically isolated (1000 Volts) from the PMC host processor board. Change-of-State Interrupts allow for an interrupt to the PCI host to be generated from any level change on any input. (PCI-OPTO32A-12V)  
CS-GS-OPTO32A-12E The CS-PCI-eOPTO32A board has 32 optically-coupled digital I/O channels consisting of 8 outputs and 24 inputs. Each channel is electrically isolated (1000 Volts) from the PMC host processor board. Change-of-State Interrupts allow for an interrupt to the PCI host to be generated from any level change on any input. (PCIe-OPTO32A-12V)  
CS-GS-OPTO32A-24 The CS-PCI-OPTO32A board has 32 optically-coupled digital I/O channels consisting of 8 outputs and 24 inputs. Each channel is electrically isolated (1000 Volts) from the PMC host processor board. Change-of-State Interrupts allow for an interrupt to the PCI host to be generated from any level change on any input. (PCI-OPTO32A-24V)  
CS-GS-OPTO32A-24E The CS-PCIe-OPTO32A board has 32 optically-coupled digital I/O channels consisting of 8 outputs and 24 inputs. Each channel is electrically isolated (1000 Volts) from the PMC host processor board. Change-of-State Interrupts allow for an interrupt to the PCI host to be generated from any level change on any input. (PCIe-OPTO32A-24V)  
CS-GS-OPTO32A-28 The CS-PCI-OPTO32A board has 32 optically-coupled digital I/O channels consisting of 8 outputs and 24 inputs. Each channel is electrically isolated (1000 Volts) from the PMC host processor board. Change-of-State Interrupts allow for an interrupt to the PCI host to be generated from any level change on any input. (PCI-OPTO32A-28V)  
CS-GS-OPTO32A-28E The CS-PCIe-OPTO32A board has 32 optically-coupled digital I/O channels consisting of 8 outputs and 24 inputs. Each channel is electrically isolated (1000 Volts) from the PMC host processor board. Change-of-State Interrupts allow for an interrupt to the PCI host to be generated from any level change on any input. (PCIe-OPTO32A-28V)  
CS-GS-OPTO32A-48 The CS-PCI-OPTO32A board has 32 optically-coupled digital I/O channels consisting of 8 outputs and 24 inputs. Each channel is electrically isolated (1000 Volts) from the PMC host processor board. Change-of-State Interrupts allow for an interrupt to the PCI host to be generated from any level change on any input. (PCI-OPTO32A-48V)  
CS-GS-OPTO32A-48E The CS-PCIe-OPTO32A board has 32 optically-coupled digital I/O channels consisting of 8 outputs and 24 inputs. Each channel is electrically isolated (1000 Volts) from the PMC host processor board. Change-of-State Interrupts allow for an interrupt to the PCI host to be generated from any level change on any input. (PCIe-OPTO32A-48V)  
CS-GS-OPTO32B-82K The CS-PCI-OPTO32B device w/ custom 8.2K Ohm resistors installed on input channels 0-23 (see note). This device has 32 optically-coupled digital I/O channels consisting of 8 outputs and 24 inputs. Each channel is electrically isolated (1000 Volts) from the PMC host processor board. Change-of-State Interrupts allow for an interrupt to the PCI host to be generated from any level change on any input. (PCI-OPTO32B-R8.2K) Note: In order to meet boards specifications, Input Voltage Values should of sufficient value to provide a minimum input current of 2.3 mA for any given custom resistor values installed on input channels. (Minimum voltage 18.86V for the resistor option provided with this board).  
CS-GS-OPTO32C-82K The PCIe-OPTO32C-R8.2K is a native PCIe device w/ custom 8.2K Ohm resistors installed on input channels 0-23 (see note). This device has 32 optically-coupled digital I/O channels consisting of 8 outputs and 24 inputs. Each channel is electrically isolated (1000 Volts) from the PMC host processor board. Change-of-State Interrupts allow for an interrupt to the PCI host to be generated from any level change on any input. (PCIe-OPTO32C-R8.2K) Note: In order to meet boards specifications, Input Voltage Values should of sufficient value to provide a minimum input current of 2.3 mA for any given custom resistor values installed on input channels. (Minimum voltage 18.86V for the resistor option provided with this board). True PCIe device. Extended lead time 10-12 weeks should be expected for this device. 
CS-GS-PMC2PCIE4 PCIE to PMC Carrier: Adapts a single-width PMC form factor to a single lane PCI Express (x4 link). Onboard DC/DC Converter, no external power requirements. Support both 3.3V and 5V Signaling, PCI & PCI-X Bus. Requires available PCI-e x4 compatible slot. (GS P/N PCIe4-to-PMC-Adapter-0)  
CS-GS-PMC2PCIE4F PCIE to PMC Carrier: Adapts a single-width PMC form factor to a single lane PCI Express (x4 link). Cooling Fan, Onboard DC/DC Converter, no external power requirements. Support both 3.3V and 5V Signaling, PCI & PCI-X Bus. Requires available PCI-e x4 compatible slot. (GS P/N PCIe4-to-PMC-Adapter-1)  
CS-GS-PMC2PCIX PCIX to PMC Carrier: Adapts a single-width PMC form factor to a single lane PCIX Slot. 64Bit PCI-X Bus to 64Bit PMC Adapter on a PCI card (short length). Operates with any combination of 64Bit or 32Bit PMC cards in 64Bit or 32Bit PCI-X Bus. Requires available PCIX compatible slot. (GS P/N PMC-TO-PCIX ADAPTER)  
CS-GS-SIO4B-A2-256 (LEGACY CARD - Not Available for New Projects) PCI-SIO4B-232-256K - PCI-SIO4B is a four channel full-duplex serial board that is available with RS232 transceivers. Each channel can operate up to 250 kbits/sec for RS232. 32 Kbytes of FIFO buffering for both transmit and receive (256 Kbytes Total FIFOs) data on each channel. Board supports Asynchronous, Isochronous, Bisync, Monosync, HDLC, SDLC, External Sync and Nine-Bit protocols. ** Replacement Card is: CS-GS-SIO4BXR-256 ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4B-A2-64 (LEGACY CARD - Not Available for New Projects) PCI-SIO4B-232-64K - PCI-SIO4B is a four channel full-duplex serial board that is available with RS232 transceivers. Each channel can operate up to 250 kbits/sec for RS232. 8 Kbytes of FIFO buffering for both transmit and receive 64 Kbytes Total FIFOs) data on each channel. Board supports Asynchronous, Isochronous, Bisync, Monosync, HDLC, SDLC, External Sync and Nine-Bit protocols. ** Replacement Card is: CS-GS-SIO4BXR-64 ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4B-A4-256 (LEGACY CARD - Not Available for New Projects) PCI-SIO4B-256K - PCI-SIO4B is a four channel full-duplex serial board that is available with RS422/485 transceivers. Each channel can operate up to 10Mbits/sec differential (RS-422/485) . 32 Kbytes of FIFO buffering for both transmit and receive (256 Kbytes Total FIFOs) data on each channel. Board supports Asynchronous, Isochronous, Bisync, Monosync, HDLC, SDLC, External Sync and Nine-Bit protocols. ** Replacement Card is: CS-GS-SIO4BXR-256 ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4B-A4-64 (LEGACY CARD - Not Available for New Projects) PCI-SIO4B-64K - PCI-SIO4B is a four channel full-duplex serial board that is available with RS422/485 transceivers. Each channel can operate up to 10Mbits/sec differential (RS-422/485) . 8 Kbytes of FIFO buffering for both transmit and receive 64 Kbytes Total FIFOs) data on each channel. Board supports Asynchronous, Isochronous, Bisync, Monosync, HDLC, SDLC, External Sync and Nine-Bit protocols.** Replacement Card is: CS-GS-SIO4BXR-64 ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4B-S2-256 (LEGACY CARD - Not Available for New Projects) PCI-SIO4B-SYNC-232-256K - RS 232 Transcivers -256K FIFO - Features Quad Channel Synchronous Serial To Parallel Controller with Optional 64K Deep Transmit and Receive FIFOs The PCI-SI04B-SYNC board is a four channel serial interface card which provides a simple synchronous serial interface capability for PCI applications. (Note: This board is a NATIVE PCI form factor and is not available for the PCIe form factor) ** Replacement Card is: CS-GS-SIO4BXR-256 ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4B-S2-64 (LEGACY CARD - Not Available for New Projects) PCI-SIO4B-SYNC-232-64K - RS 232 Transcivers - 64K FIFO - Features Quad Channel Synchronous Serial To Parallel Controller with Optional Deep 8KTransmit and Receive FIFOs The PCI-SI04B-SYNC board is a four channel serial interface card which provides a simple synchronous serial interface capability for PCI applications. (Note: This board is a NATIVE PCI form factor and is not available for the PCIe form factor) ** Replacement Card is: CS-GS-SIO4BXR-64 ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4B-S4-256 (LEGACY CARD - Not Available for New Projects) PCI-SIO4B-SYNC-256K - RS 485/422 Transcivers -256K FIFO - Features Quad Channel Synchronous Serial To Parallel Controller with Optional Deep 32K Transmit and Receive FIFOs The PCI-SI04B-SYNC board is a four channel serial interface card which provides a simple synchronous serial interface capability for PCI applications. (Note: This board is a NATIVE PCI form factor and is not available for the PCIe form factor) ** Replacement Card is: CS-GS-SIO4BXR-256 ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4B-S4-64 (LEGACY CARD - Not Available for New Projects) PCI-SIO4B-SYNC-64K - RS 485/422 Transcivers - 64K FIFO - Features Quad Channel Synchronous Serial To Parallel Controller with Optional Deep 8K Transmit and Receive FIFOs The PCI-SI04B-SYNC board is a four channel serial interface card which provides a simple synchronous serial interface capability for PCI applications. (Note: This board is a NATIVE PCI form factor and is not available for the PCIe form factor) ** Replacement Card is: CS-GS-SIO4BXR-64 ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4BX-A256E (LEGACY CARD - Not Available for New Projects) PCIe-SIO4BX-256K - four, high-speed synchronous serial interface channels for PCIe applications w/ 32K byte FIFOs on each chan (both Tx & Rx, 8 total) . This is a high-speed serial card that features the Zilog Z16C30 serial controller chips. This card is best used when the serial protocol will be one of the industry standards such as HDLC/SDLC, asynchronous, isochronous, bisync or monosync. The Zilog chips will handle the protocol specific overhead and add/strip extra information from the serial data stream to make it match the requested protocol. ** Replacement Card is: CS-GS-SIO4BXR-256E ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4BX-A256K (LEGACY CARD - Not Available for New Projects) PCI-SIO4BX-256K - four, high-speed synchronous serial interface channels for PCI applications w/ 32K byte FIFOs on each chan (both Tx & Rx, 8 total) . This is a high-speed serial card that features the Zilog Z16C30 serial controller chips. This card is best used when the serial protocol will be one of the industry standards such as HDLC/SDLC, asynchronous, isochronous, bisync or monosync. The Zilog chips will handle the protocol specific overhead and add/strip extra information from the serial data stream to make it match the requested protocol. ** Replacement Card is: CS-GS-SIO4BXR-256 ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4BX-A4E (LEGACY CARD - Not Available for New Projects) PCIe-SIO4BX-4KLC - four, high-speed synchronous serial interface channels for PCIe applications w/ 512 byte FIFOs on each chan (both Tx & Rx, 8 total) . This is a high-speed serial card that features the Zilog Z16C30 serial controller chips. This card is best used when the serial protocol will be one of the industry standards such as HDLC/SDLC, asynchronous, isochronous, bisync or monosync. The Zilog chips will handle the protocol specific overhead and add/strip extra information from the serial data stream to make it match the requested protocol. ** Replacement Card is: CS-GS-SIO4BXR-64E ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4BX-A4K (LEGACY CARD - Not Available for New Projects) PCI-SIO4BX-4KLC - four, high-speed synchronous serial interface channels for PCI applications w/ 512 byte FIFOs on each chan (both Tx & Rx, 8 total) . This is a high-speed serial card that features the Zilog Z16C30 serial controller chips. This card is best used when the serial protocol will be one of the industry standards such as HDLC/SDLC, asynchronous, isochronous, bisync or monosync. The Zilog chips will handle the protocol specific overhead and add/strip extra information from the serial data stream to make it match the requested protocol. ** Replacement Card is: CS-GS-SIO4BXR-64 ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4BX-A64E (LEGACY CARD - Not Available for New Projects) PCIe-SIO4BX-64K - four, high-speed synchronous serial interface channels for PCIe applications w/ 8K byte FIFOs on each chan (both Tx & Rx, 8 total) . This is a high-speed serial card that features the Zilog Z16C30 serial controller chips. This card is best used when the serial protocol will be one of the industry standards such as HDLC/SDLC, asynchronous, isochronous, bisync or monosync. The Zilog chips will handle the protocol specific overhead and add/strip extra information from the serial data stream to make it match the requested protocol. ** Replacement Card is: CS-GS-SIO4BXR-64E ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4BX-A64K (LEGACY CARD - Not Available for New Projects) PCI-SIO4BX-64K - four, high-speed synchronous serial interface channels for PCI applications w/ 8K byte FIFOs on each chan (both Tx & Rx, 8 total) . This is a high-speed serial card that features the Zilog Z16C30 serial controller chips. This card is best used when the serial protocol will be one of the industry standards such as HDLC/SDLC, asynchronous, isochronous, bisync or monosync. The Zilog chips will handle the protocol specific overhead and add/strip extra information from the serial data stream to make it match the requested protocol. ** Replacement Card is: CS-GS-SIO4BXR-64 ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4BX-S256 (LEGACY CARD - Not Available for New Projects) PCI-SIO4BX-SYNC-256K - four, high-speed synchronous serial interface channels for PCI applications. The SIO4BX-SYNC combines a flexible serial/parallel converter, deep FIFO data buffers, and multiprotocol transceivers in four fully independent synchronous serial IO channels. 10Mbits/sec 32k FIFO, RS485/RS422 Differential cable transceivers. The SIO4BX-SYNC family does not support higher level protocols such as HDLC/SDLC. This card is best used when the customer is using a proprietary serial protocol that can be decoded in software by the customer's applicaiton. ** Replacement Card is: CS-GS-SIO4BXR-256 ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4BX-S256E (LEGACY CARD - Not Available for New Projects) PCIe-SIO4BX-SYNC-256K - four, high-speed synchronous serial interface channels for PCIe applications. The SIO4BX-SYNC combines a flexible serial/parallel converter, deep FIFO data buffers, and multiprotocol transceivers in four fully independent synchronous serial IO channels. 10Mbits/sec 32k FIFO, RS485/RS422 Differential cable transceivers. The SIO4BX-SYNC family does not support higher level protocols such as HDLC/SDLC. This card is best used when the customer is using a proprietary serial protocol that can be decoded in software by the customer's applicaiton. ** Replacement Card is: CS-GS-SIO4BXR-256E ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4BX-S4 (LEGACY CARD - Not Available for New Projects) PCI-SIO4BX-SYNC-4KLC - four, high-speed synchronous serial interface channels for PCI applications. The SIO4BX-SYNC combines a flexible serial/parallel converter, deep FIFO data buffers, and multiprotocol transceivers in four fully independent synchronous serial IO channels. 10Mbits/sec 512 Byte FIFO, RS485/RS422 Differential cable transceivers. The SIO4BX-SYNC family does not support higher level protocols such as HDLC/SDLC. This card is best used when the customer is using a proprietary serial protocol that can be decoded in software by the customer's applicaiton. ** Replacement Card is: CS-GS-SIO4BXR-64 ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4BX-S4E (LEGACY CARD - Not Available for New Projects) PCIe-SIO4BX-SYNC-4KLC - four, high-speed synchronous serial interface channels for PCIe applications. The SIO4BX-SYNC combines a flexible serial/parallel converter, deep FIFO data buffers, and multiprotocol transceivers in four fully independent synchronous serial IO channels. 10Mbits/sec 512 Byte FIFO, RS485/RS422 Differential cable transceivers. The SIO4BX-SYNC family does not support higher level protocols such as HDLC/SDLC. This card is best used when the customer is using a proprietary serial protocol that can be decoded in software by the customer's applicaiton. ** Replacement Card is: CS-GS-SIO4BXR-64E ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4BX-S64 (LEGACY CARD - Not Available for New Projects) PCI-SIO4BX-SYNC-64K - four, high-speed synchronous serial interface channels for PCI applications. The SIO4BX-SYNC combines a flexible serial/parallel converter, deep FIFO data buffers, and multiprotocol transceivers in four fully independent synchronous serial IO channels. 10Mbits/sec 8k FIFO, RS485/RS422 Differential cable transceivers. The SIO4BX-SYNC family does not support higher level protocols such as HDLC/SDLC. This card is best used when the customer is using a proprietary serial protocol that can be decoded in software by the customer's applicaiton. ** Replacement Card is: CS-GS-SIO4BXR-64 ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4BX-S64E (LEGACY CARD - Not Available for New Projects) PCIe-SIO4BX-SYNC-64K - four, high-speed synchronous serial interface channels for PCIe applications. The SIO4BX-SYNC combines a flexible serial/parallel converter, deep FIFO data buffers, and multiprotocol transceivers in four fully independent synchronous serial IO channels. 10Mbits/sec 8k FIFO, RS485/RS422 Differential cable transceivers. The SIO4BX-SYNC family does not support higher level protocols such as HDLC/SDLC. This card is best used when the customer is using a proprietary serial protocol that can be decoded in software by the customer's applicaiton. ** Replacement Card is: CS-GS-SIO4BXR-64E ** General Standards has listed this cards as Legacy I/O - It should not be quoted for any new projects. For New Projects: Quote the CS-GS-SIO4BXR-XXX card. 
CS-GS-SIO4BX2 PCIe-SIO4BX2 -High-performance Multi-Protocol Serial I/O with Software Configurable Cable Transceivers (RS422, RS232 and others). 32K byte FIFOs on each chan (both Tx & Rx, 8 total) (GS p/n PCIe-SIO4BX2)  
CS-GS-SIO4BX2-S PCIe-SIO4BX2-Sync -Quad Channel Synchronous Serial To Parallel Controller with Software Configurable Cable Transceivers (RS422, RS232 and others). 32K byte FIFOs on each chan (both Tx & Rx, 8 total) (GS p/n PCIe-SIO4BX2-SYNC)  
CS-GS-SIO4BXR-256 PCI66-SIO4BXR-256K - Front or Rear I/O - Four channel serial interface card which provides high speed, full-duplex, Multi-Protocol Serial I/O with software configurable cable transceivers (RS422, RS232 and others) with Rear I/O. 32K byte FIFOs on each chan (both Tx & Rx, 8 total) . The SIO4BXR combines two multi-protocol Dual Universal Serial Controllers (USC®), 8 external FIFOs, and multi-protocol transceivers to provide four fully independent asynchronous or synchronous serial channels. Multiprotocol Transceivers support RS422 (V.11)/RS485, RS423 (V.10), RS232 (V.28), V.35, RS530, as well as other Mixed Protocol modes.  
CS-GS-SIO4BXR-256E PCIe-SIO4BXR-256K - Front or Rear I/O - Four channel serial interface card which provides high speed, full-duplex, Multi-Protocol Serial I/O with software configurable cable transceivers (RS422, RS232 and others) with Rear I/O. 32K byte FIFOs on each chan (both Tx & Rx, 8 total) . The SIO4BXR combines two multi-protocol Dual Universal Serial Controllers (USC®), 8 external FIFOs, and multi-protocol transceivers to provide four fully independent asynchronous or synchronous serial channels. Multiprotocol Transceivers support RS422 (V.11)/RS485, RS423 (V.10), RS232 (V.28), V.35, RS530, as well as other Mixed Protocol modes.  
CS-GS-SIO4BXR-64 PCI66-SIO4BXR-64K - Front or Rear I/O - Four channel serial interface card which provides high speed, full-duplex, Multi-Protocol Serial I/O with software configurable cable transceivers (RS422, RS232 and others) with Rear I/O. 8K byte FIFOs on each chan (both Tx & Rx, 8 total). The SIO4BXR combines two multi-protocol Dual Universal Serial Controllers (USC®), 8 external FIFOs, and multi-protocol transceivers to provide four fully independent asynchronous or synchronous serial channels. Multiprotocol Transceivers support RS422 (V.11)/RS485, RS423 (V.10), RS232 (V.28), V.35, RS530, as well as other Mixed Protocol modes.  
CS-GS-SIO4BXR-64E PCIe-SIO4BXR-64K - Front or Rear I/O - Four channel serial interface card which provides high speed, full-duplex, Multi-Protocol Serial I/O with software configurable cable transceivers (RS422, RS232 and others) with Rear I/O. 8K byte FIFOs on each chan (both Tx & Rx, 8 total). The SIO4BXR combines two multi-protocol Dual Universal Serial Controllers (USC®), 8 external FIFOs, and multi-protocol transceivers to provide four fully independent asynchronous or synchronous serial channels. Multiprotocol Transceivers support RS422 (V.11)/RS485, RS423 (V.10), RS232 (V.28), V.35, RS530, as well as other Mixed Protocol modes.  
CS-GS-SIO8BX-A128K PCI-SIO8BXS-128K - eight channel serial interface card which provides high speed, full-duplex, multi-protocol serial capability. The SIO8BX combines four multi-protocol Dual Universal Serial Controllers (USC®), 16 external FIFOs, and multi-protocol transceivers to provide eight fully independent asynchronous or synchronous serial channels. Multiprotocol Transceivers support RS422 (V.11)/RS485, RS423 (V.10), RS232 (V.28), V.35, RS530, as well as other Mixed Protocol modes. The Zilog chips will handle the protocol specific overhead and add/strip extra information from the serial data stream to make it match the requested protocol.  
CS-GS-SIO8BX-A512K PCI-SIO8BXS-512K - eight channel serial interface card which provides high speed, full-duplex, multi-protocol serial capability. The SIO8BX combines four multi-protocol Dual Universal Serial Controllers (USC®), 16 external FIFOs, and multi-protocol transceivers to provide eight fully independent asynchronous or synchronous serial channels. Multiprotocol Transceivers support RS422 (V.11)/RS485, RS423 (V.10), RS232 (V.28), V.35, RS530, as well as other Mixed Protocol modes. The Zilog chips will handle the protocol specific overhead and add/strip extra information from the serial data stream to make it match the requested protocol.  
CS-GS-SIO8BX-A8K PCI-SIO8BXS-8KLC - eight channel serial interface card which provides high speed, full-duplex, multi-protocol serial capability. The SIO8BX combines four multi-protocol Dual Universal Serial Controllers (USC®), 16 external FIFOs, and multi-protocol transceivers to provide eight fully independent asynchronous or synchronous serial channels. Multiprotocol Transceivers support RS422 (V.11)/RS485, RS423 (V.10), RS232 (V.28), V.35, RS530, as well as other Mixed Protocol modes. The Zilog chips will handle the protocol specific overhead and add/strip extra information from the serial data stream to make it match the requested protocol.  
       Highland Technology Frequency and Arbitrary Waveform Generator
CS-HT-V360 8-channel Period, Frequency & RPM measurement  
CS-HT-V370 4-channel Arbitrary Waveform Generator VME card  
       Intel Ethernet
CS-INT-DELA0097930 Intel Pro/1000MT Quad Ethernet PCI-X card (requires a PCI-X slot only - Not for use in a PCI 33MHz Slot).  
CS-INT-E1G44ET2 (Std. Profile) Intel Gigabit ET2 Quad Port Server Adapter - Network adapter - PCIe - 10Mb LAN, 100Mb LAN, Gigabit LAN - 10Base-T, 100Base-TX, 1000Base-T - 4 ports - Replaces CS-INT-EXPI9404PT. May not be supported on motherboards that have on-board Intel 82576 Gigabit Ethernet controllers 
CS-INT-E1G44ET2L (Low Profile) Intel Gigabit ET2 Quad Port Server Adapter - Network adapter - PCIe - 10Mb LAN, 100Mb LAN, Gigabit LAN - 10Base-T, 100Base-TX, 1000Base-T - 4 ports - Replaces CS-INT-EXPI9404PTL May not be supported on motherboards that have on-board Intel 82576 Gigabit Ethernet controllers 
       MOXA Serial
CS-MX-CBL-M25x4 MOXA CBL-M44M25x4-50 - Male DB44 to 4x Male DB25 Cable for the CS-MX-CP134U).  
CS-MX-CBL-M25x8 MOXA CBL-M62M25x8-100 - Male DB62 to 8x Male DB25 Cable for the CS-MX-CP118U.  
CS-MX-CBL-M68M9x8 MOXA CBL-M68M9x8-100 - Male DB68 to 8x Male DB9 Cable for the CS-MX-CP118EL-A.  
CS-MX-CBL-M68x8 MOXA CBL-M68M25x8-100 - Male DB68 to 8x Male DB25 Cable for the CS-MX-CP118EL-A.  
CS-MX-CBL-M7825x8 MOXA CBL-M78M25x8-100 -8-port connection cable (board-side: DB78 male x 1; device-side: DB25 male x 8), 100 cm. Cable for the CS-MX-CP118U-I & CS-MX-CP134U-I.  
CS-MX-CBL-M78x8 MOXA CBL-M78M9x8-100 -8-port connection cable (board-side: DB78 male x 1; device-side: DB9 male x 8), 100 cm. Cable for the CS-MX-CP118U-I & CS-MX-CP134U-I.  
CS-MX-CBL-M9x4 MOXA CBL-M44M9x4-50 - Male DB44 to 4x Male DB9 Cable for the CS-MX-CP1x.  
CS-MX-CBL-M9x8 MOXA CBL-M62M9x8-100 - Male DB62 to 8x Male DB9 Cable for the CS-MX-CP1x.  
CS-MX-CP114EL-25 MOXA CP-114EL-DB25: PCIe x1 - 4 RS232/RS422/RS485 ports, data rates up to 921.6Kbps, modem control signals, Asynchronous Serial support. Interrupt driven I/O for real time performance. (Includes DB25 male cable) Quotation from your salesman is required for SimWB support if a non-generic serial protocol is required. Please ask your salesman if a quotation is required. 
CS-MX-CP114EL-9 MOXA CP-114EL-DB9M: PCIe x1 - 4 RS232/RS422/RS485 ports, data rates up to 921.6Kbps, modem control signals, Asynchronous Serial support. Interrupt driven I/O for real time performance. (Includes DB9 male cable) Quotation from your salesman is required for SimWB support if a non-generic serial protocol is required. Please ask your salesman if a quotation is required. 
CS-MX-CP114EL-I-25 MOXA CP-114EL-I-DB25: (Isolated) PCIe x1 - 4 RS232/RS422/RS485 ports, data rates up to 921.6Kbps, modem control signals, Asynchronous Serial support. Interrupt driven I/O for real time performance. (Includes DB25 male cable) Quotation from your salesman is required for SimWB support if a non-generic serial protocol is required. Please ask your salesman if a quotation is required. 
CS-MX-CP114EL-I-9 MOXA CP-114EL-I-DB9M: (Isolated) PCIe x1 - 4 RS232/RS422/RS485 ports, data rates up to 921.6Kbps, modem control signals, Asynchronous Serial support. Interrupt driven I/O for real time performance. (Includes DB9 male cable) Quotation from your salesman is required for SimWB support if a non-generic serial protocol is required. Please ask your salesman if a quotation is required. 
CS-MX-CP114UL-25 MOXA CP-114UL-DB25M: PCI - 4 RS232/RS422/RS485 ports, data rates up to 921.6Kbps, modem control signals, 3.3V & 5V PCI buses, Asynchronous Serial support. Interrupt driven I/O for real time performance. (Includes DB25 male cable) Quotation from your salesman is required for SimWB support if a non-generic serial protocol is required. Please ask your salesman if a quotation is required. 
CS-MX-CP114UL-9 MOXA CP-114UL-DB9M: PCI - 4 RS232/RS422/RS485 ports, data rates up to 921.6Kbps, modem control signals, 3.3V & 5V PCI buses, Asynchronous Serial support. Interrupt driven I/O for real time performance. (Includes DB9 male cable) Quotation from your salesman is required for SimWB support if a non-generic serial protocol is required. Please ask your salesman if a quotation is required. 
CS-MX-CP114UL-I-25 MOXA CP-114UL-I-DB25: (Isolated) PCI - 4 RS232/RS422/RS485 ports with 2KV Optical Isolation, data rates up to 921.6Kbps, modem control signals, 3.3V & 5V PCI buses, Asynchronous Serial support. Interrupt driven I/O for real time performance. (Includes DB25 male cable) Quotation from your salesman is required for SimWB support if a non-generic serial protocol is required. Please ask your salesman if a quotation is required. 
CS-MX-CP114UL-I-9 MOXA CP-114UL-I-DB9: (Isolated) PCI - 4 RS232/RS422/RS485 ports with 2KV Optical Isolation, data rates up to 921.6Kbps, modem control signals, 3.3V & 5V PCI buses, Asynchronous Serial support. Interrupt driven I/O for real time performance. (Includes DB9 male cable) Quotation from your salesman is required for SimWB support if a non-generic serial protocol is required. Please ask your salesman if a quotation is required. 
CS-MX-CP118EL-A MOXA CP-118EL-A: PCIe - 8 RS232/RS422/RS485 ports, data rates up to 921.6Kbps, modem control signals, 128-byte FIFO and on-chip H/W, S/W flow control. Low Profile form factor. PCIe x1 compatible slot required. (Requires purchase of additional cable.) Quotation from your salesman is required for SimWB support if a non-generic serial protocol is required. Please ask your salesman if a quotation is required. 
CS-MX-CP118U MOXA CP-118U: PCI - 8 RS232/RS422/RS485 ports, data rates up to 921.6Kbps, modem control signals, 3.3V & 5V PCI buses, Asynchronous Serial support. Interrupt driven I/O for real time performance. (Requires purchase of additional cable.) Quotation from your salesman is required for SimWB support if a non-generic serial protocol is required. Please ask your salesman if a quotation is required. 
CS-MX-CP118U-I MOXA CP-118U-I: (Isolated) PCI - 8 RS232/RS422/RS485 ports with 2KV Optical Isolation, data rates up to 921.6Kbps, modem control signals, 3.3V & 5V PCI buses, Asynchronous Serial support. Interrupt driven I/O for real time performance. (Requires purchase of additional cable.) Quotation from your salesman is required for SimWB support if a non-generic serial protocol is required. Please ask your salesman if a quotation is required. 
CS-MX-CP134U MOXA CP-134U: PCI - 4 RS232/RS422/RS485 ports, data rates up to 921.6Kbps, modem control signals, 3.3V & 5V PCI buses, Asynchronous Serial support. Only ports 1 and 2 support RS232 communication. Interrupt driven I/O for real time performance. (Requires purchase of additional cable.) Quotation from your salesman is required for SimWB support if a non-generic serial protocol is required. Please ask your salesman if a quotation is required. 
CS-MX-CP134U-I MOXA CP-134U-I: (Isolated) PCI - 4 RS232/RS422/RS485 ports with 2KV Optical Isolation, data rates up to 921.6Kbps, modem control signals, 3.3V & 5V PCI buses, Asynchronous Serial support. Only ports 1 and 2 support RS232 communication. Interrupt driven I/O for real time performance. (Requires purchase of additional cable.) Quotation from your salesman is required for SimWB support if a non-generic serial protocol is required. Please ask your salesman if a quotation is required. 
CS-MX-OPT8-A MOXA OPT8A+ - VHDCI 68 to DB25 female x 8 RS-232 Connection Box Includes VHDCI 68 to DB62 male, 150 cm connection Cable for the CS-MX-CP1x.  
CS-MX-OPT8-M9 MOXA OPT8-M9 - DB62(M) to 8 x DB9(M) RS-232 Connection Box for the CS-MX-CP1x. Includes DB62 male to DB62 female 150 cm connection Cable for connecting to the serial board.  
       North Atlantic Industries RVDT, LVDT, Synchro and Resolver
CS-NA-76CL1-26-05 NAII 76CL1-026CL1-05 RVDT 6-Channel two measurement channels, on-board reference signal 2-28VRMS Output It is strongly suggested that you contact your salesman to ensure that this board will meet the requirements of your customer.  
CS-NA-76CL1-44-04 NAII 76CL1-044CLA-04 LVDT device w/ 4-D/L Simulation Output channels, 4-L/D Measurement Input Channels, 2-28VRMS Excitation Output, 2.69KHz Excitation Frequency It is strongly suggested that you contact your salesman to ensure that this board will meet the requirements of your customer.  
CS-NA-76CL1-80-85 NAII 76CL1-080CLA-85 LVDT device w/ 0-D/L Simulation Output channels, 8-L/D Measurement Input Channels, 0° to 70°C, On-board Reference 2-28VRMS Output, No Encoder/Commutation Option, 85= LD: CH1 to 8 = 2-28V, 10kHz Frequency. It is strongly suggested that you contact your salesman to ensure that this board will meet the requirements of your customer.  
CS-NA-76CL1-86-04 NAII 76CL1-086CLA-04 LVDT device w/ 6-D/L Simulation Output channels, 8-L/D Measurement Input Channels, 2-28VRMS Excitation Output, 2.69KHz Excitation Frequency It is strongly suggested that you contact your salesman to ensure that this board will meet the requirements of your customer.  
CS-NA-76CS1-02-KG NAII 76CS1-002CRA-KG 0 Channel S/D 2-Channel D/S Resolver: 0° to 70°C, On-board Reference 2-28V, No Encoder/Commutation Option, KG= DR: 10VLL / 10Vref / 10KHz Frequency all channels. It is strongly suggested that you contact your salesman to ensure that this board will meet the requirements of your customer.  
CS-NA-76CS1-06-CO NAII 76CS1-006CRO-CO 6-Channel Resolver Only: 3000 HZ @ 6 VRMS It is strongly suggested that you contact your salesman to ensure that this board will meet the requirements of your customer.  
CS-NA-76CS1-06-CP NAII 76CS1-006CRO-CP 6-Channel Resolver Only: 5400 HZ @ 5.5 VRMS It is strongly suggested that you contact your salesman to ensure that this board will meet the requirements of your customer.  
CS-NA-76CS1-26-CO NAII 76CS1-026CRA-C0 6-Channel Resolver two measurement channels, on-board reference signal 2-28VRMS Output: 3000 HZ @ 6 VRMS It is strongly suggested that you contact your salesman to ensure that this board will meet the requirements of your customer.  
CS-NA-76CS1-26-CP NAII 76CS1-026CRA-CP 6-Channel Resolver two measurement channels, on-board reference signal 2-28VRMS Output: 5400 HZ @ 5.4 VRMS It is strongly suggested that you contact your salesman to ensure that this board will meet the requirements of your customer.  
CS-NA-76CS1-86-GV NAII 76CS1-086CSA-GV Synchro device, 8-S/D Measurement Input Channels, 6-D/S Synchro Output Channels, 2-28VRMS Excitation Output, 2.69KHz Excitation Frequency It is strongly suggested that you contact your salesman to ensure that this board will meet the requirements of your customer.  
       National Instruments Data Acquisition
CS-NI-182482-01 Unshielded Screw Terminal Connectivity Accessory Set. 1m unshielded Ribbon Cable R6868 and CB-68LP I/O Connector Block for the CS-NI-PCI-6023E, CS-NI-PCI-6024E, CS-NI-PCI-6034E and CS-NI-PCI-6036E. Accessory for PCI-6023E, PCI-6024E, PCI-6034E, PCI-6036E (Includes NI 777145-01) 
CS-NI-182762-01 R1005050-01 (p/n 182762-01) 1-meter Unsheilded Ribbon cable that connects to a CS-NI-PCI-DIO-96 or CS-NI-PCI-6509 and is terminated with two 50-pin IDC connectors.  
CS-NI-182762-02 R1005050-02 (p/n 182762-02) 2-meter Unsheilded Ribbon cable that connects to a CS-NI-PCI-DIO-96 or CS-NI-PCI-6509 and is terminated with two 50-pin IDC connectors.  
CS-NI-182853-01 SH100100 1-meter Shielded Cable for the CS-NI-PCI-6025E, CS-NI-PCI-6031E, CS-NI-PCI-6033E and CS-NI-PCI-6071E Accessory for CS-NI-PCI-6025E, CS-NI-PCI-6031E, CS-NI-PCI-6071E. 
CS-NI-183432-01 SH-68-68-D1 1-meter Shielded Cable for the CS-NI-PCI-6704, CS-NI-PCI-6703 and CS-NI-PCI-6602 Accessory forCS-NI- PCI-6704, CS-NI-PCI-6703, CS-NI-PCI-6602 
CS-NI-184749-01 SH68-68-EP 1-meter Shielded Cable for the CS-NI-PCI-6023E, CS-NI-PCI-6024E, CS-NI-PCI-6032E, CS-NI-PCI-6034E, CS-NI-PCI-6036E, CS-NI-PCI-6052E and CS-NI-PCI-6070E  
CS-NI-185095-02 SH100-100-F 2-meter Shielded Cable for the CS-NI-PCI-DIO-96 PCI-DIO-96 
CS-NI-763061-02 IEEE-488 2 Meter Cable for the CS-NI-PCI-GPIB/LP Accessory for CS-NI-PCI-GBIB/LP 
CS-NI-776164-90 CB-50 I/O Connector Block with DIN Rail Mounting without cable for the CS-NI-PCI-DIO-96 Accessory for CS-NI-PCI-DIO-96 & CS-NI-PCI-6509 
CS-NI-776844-01 SCB-68 Shielded Cable I/O Connector Block for the CS-NI-PCI-6032E, CS-NI-PCI-6052E, CS-NI-PCI-6070E, CS-NI-PCI-6704, CS-NI-PCI-6703 and CS-NI-PCI-6602  
CS-NI-776990-01 SCB-100 Shielded Cable I/O Connector Block for the CS-NI-PCI-6025E, CS-NI-PCI-6031E, CS-NI-PCI-6033E and CS-NI-PCI-6071E. Accessory for CS-NI-PCI-6025E & CS-NI-PCI-6071E 
CS-NI-777141-01 TBX-68 Unshielded, I/O Connector Block with DIN-Rail Mounting for the CS-NI-PCI-6032E, CS-NI-PCI-6052E, CS-NI-PCI-6070E, CS-NI-PCI-6704, CS-NI-PCI-6703 and CS-NI-PCI-6602  
CS-NI-777145-01 CB-68LP Unshielded, low cost I/O Connector Block or the CS-NI-PCI-6032E, CS-NI-PCI-6052E, CS-NI-PCI-6070E, CS-NI-PCI-6704, CS-NI-PCI-6703 and CS-NI-PCI-6602  
CS-NI-777643-01 BNC Cable Accessory for the CS-NI-PCI-6023E, CS-NI-PCI-6024E, CS-NI-PCI-6032E, CS-NI-PCI-6034E and CS-NI-PCI-6036E  
CS-NI-777812-01 CB-100 I/O Kit DIN/panel/desktop, 50 pin 1-meter Cable for the CS-NI-PCI-DIO-96 Accessory for CS-NI-PCI-DIO-96 & CS-NI-PCI-6509 
CS-NI-PCI-6023E 12-bit 200 KS/s 16 AI, 8 DIO channels RedHawk Linux Driver is not available for this device. Device supported only via SimWB. 
CS-NI-PCI-6024E 12-bit 200 KS/s 16 AI, 2 AO, 8 DIO channels RedHawk Linux Driver is not available for this device. Device supported only via SimWB. 
CS-NI-PCI-6025E 12-bit 200 KS/s 16 AI, 2 AO, 32 DIO channels (Note: SimWB only support 8 Digital I/O channels for the NI6025 card which are directly connected to the DAQ-STC chip found on the board (DIO0-DIO7) RedHawk Linux Driver is not available for this device. Device supported only via SimWB. 
CS-NI-PCI-6031E EOL - No longer available - 16-bit 100 KS/s 64 AI, 2 AO, 8 DIO channels - Alternate Device: CS-NI-PCI-6034E This item has been discontinued by the vendor. 
CS-NI-PCI-6032E EOL - No longer available - 16-bit 100 KS/s 16 AI, 8 DIO channels - Alternate Device: CS-NI-PCI-6034E This item has been discontinued by the vendor. 
CS-NI-PCI-6033E EOL - No longer available - 16-bit 100 KS/s 64 AI, 8 DIO channels - Alternate Device: CS-NI-PCI-6034E This item has been discontinued by the vendor. 
CS-NI-PCI-6034E 16-bit 200 KS/s 16 AI, 8 DIO channels RedHawk Linux Driver is not available for this device. Device supported only via SimWB. 
CS-NI-PCI-6036E 16-bit 200 KS/s 16 AI, 2 AO, 8 DIO channels RedHawk Linux Driver is not available for this device. Device supported only via SimWB. 
CS-NI-PCI-6052E 16-bit 333 KS/s 16 AI, 2 AO, 8 DIO channels RedHawk Linux Driver is not available for this device. Device supported only via SimWB. 
CS-NI-PCI-6070E 12-bit 1.25 MS/s 16 AI, 2 AO, 8 DIO channels RedHawk Linux Driver is not available for this device. Device supported only via SimWB. 
CS-NI-PCI-6071E 12-bit 1.25 MS/s 64 AI, 2 AO, 8 DIO channels RedHawk Linux Driver is not available for this device. Device supported only via SimWB. 
CS-NI-PCI-6509 NI PCI-6509 PCI/PCI-X Device -96 bidirectional digital I/O lines, 5 V TTL/CMOS (line direction selectable on an 8-bit port basis) (Compatible with DIO96 cables and connector blocks) This product has a Concurrent Developed RedHawk Kernel Driver 
CS-NI-PCI-6602 Eight 32-bit counter/timers and up to 32 lines of TTL/CMOS-compatible digital I/O, ncoder position measurement, event counting, period measurement, pulse width measurement, pulse generation, pulse train generation and frequency measurement. Software support through SIMulation Workbench only. Standalone driver not available. RedHawk driver is not available. Device supported is supported Pre-6.0 OS release only in two ways: (1) Standalone w/DAQmx or (2) SimWB w/DAQmx DAQmx requires an RIQ and is limited to 32-bit only and < 4GB memory. ***DAQmx cannot be supported beyond RedHawk 5.4 due to limitations imposed by National Instruments Linux support*** 
CS-NI-PCI-6703 16-line Static Analog Voltage Outputs -- 16-Bit. --- (This device requires purchase of SWB and applicable license - RedHawk driver is not available.) RedHawk Linux Driver is not available for this device. Device supported only via SimWB. 
CS-NI-PCI-6704 16-line Static Analog Voltage & Current Outputs -- 16-Bit (This device requires purchase of SWB and applicable license - RedHawk driver is not available.) RedHawk Linux Driver is not available for this device. Device supported only via SimWB. 
CS-NI-PCI-DIO-96 **This device is not recommended for new designs.** Please use CS-NI-PCI-6509 as a recommended replacement. National Instrument 96-bit Digital I/O board. (PCI-DIO96) Supported by RedHawk and SimWB. This item should be used only for legacy applications in which the CS-NI-PCI-DIO-96 is already in use. 
CS-NI-PCI-DIO-CBL Custom Cable for the CS-NI-PCI-DIO-96 card. 6.5M Ribbon Cable with 100pin SCSI D-sub and two DB50. Custom Cable for the PCI-DIO 96 CABLE6.5-DIO96-DB50S-ORBITAL  
CS-NI-PCI-GPIB/LP High-Performance IEEE-488 GPIB Controller for Low-Profile PCI - Ships with the RedHawk implementation of the Open Source Sourceforge driver.  
CS-NI-PCIE-6509 NI PCIe-6509 Device -96 bidirectional digital I/O lines, 5 V TTL/CMOS (line direction selectable on an 8-bit port basis) (Compatible with DIO96 cables and connector blocks) This product requires a new kernel driver and is not compatible with the PCI version of the driver. 
       Omega Counter/Time/DIO
CS-OME-TMC12 The OME-PCI-TMC12 is a PCI-Bus general purpose counter/ timer and digital I/O board. It provides twelve 16-bit counter/ timer channels. Two internal clock sources (8M /1.6M and 0.8M / 80K) are selected by jumper. Four 8254 chips provide a variety of powerful counter/timer function modes to match your industrial and laboratory applications. (Vendor p/n OME-PCI-TMC12) This card is a PCI 32-bit 5V only device. Requires a native PCI 5V slot location. 
       Precision Analog Systems COS/TTE
CS-PAS-2080-000 The PAS 2080/DIO is a PCI based, 32 channel Change Of State, (COS), detector and 8 channel, Time To Edge, (TTE), pattern generator with 1 uSec resolution. Separate input and output FIFO’s are provided to elastically buffer the input and output data patterns from the PCI bus. A 40 bit , 1 MHz counter that can be set and enabled from the PCI bus is also provided to time stamp the input data, and to determine when the output patterns are updated. **Note - For use with SIMulation WorkBench, a RCIM w/ custom Oscillator may be required. Please contact Home Office for further information **  
CS-PAS-9795DIO 80 Channel TTL Level Digital Input / Digital Output VME board  
       Pickering Relay and Resistor Simulator
CS-PIC-40-971-1M 1 Meter Cable for the CS-PIC-50-110-x relay cards. 200 Pin Connector to Connector Assembly - LFH Male to 50-Way D-type - Braided Sleeve Over Outer Layers - Metal Screwlocks 4-40 UNC - Uses 1A Rated Twisted Pair. O/D 10mm. (Pickering p/n: 40-971-200D-1M) It is strongly suggested that you contact your salesman to ensure that this board will meet the requirements of your customer.  
CS-PIC-40-971-2M 2 Meter Cable for the CS-PIC-50-110-x relay cards. 200 Pin Connector to Connector Assembly - LFH Male to 50-Way D-type - Braided Sleeve Over Outer Layers - Metal Screwlocks 4-40 UNC - Uses 1A Rated Twisted Pair. O/D 10mm. (Pickering p/n: 40-971-200D-2M) It is strongly suggested that you contact your salesman to ensure that this board will meet the requirements of your customer.  
CS-PIC-50-110-021 PCI 5V Reed Relay Card - 32 channel SPDT, Ruthenium Relays, Fast Operating 250 usec typical, 150Vdc/100Vac, Max. Power 3W for SPDT, Max Switch Current: 0.25A for SPDT. This item requires connector CS-PIC-40-971-1M or CS-PIC-40-971-2m available through the Custom Catalog. It is strongly suggested that you contact your salesman to ensure that this board will meet the requirements of your customer.  
CS-PIC-50-110-121 PCI 5V Reed Relay Card - 64 channel SPDT, Ruthenium Relays, Fast Operating 250 usec typical, 150Vdc/100Vac, Max. Power 3W for SPDT, Max Switch Current: 0.25A for SPDT. This item requires connector CS-PIC-40-971-1M or CS-PIC-40-971-2m available through the Custom Catalog. It is strongly suggested that you contact your salesman to ensure that this board will meet the requirements of your customer.  
CS-PIC-50-295 PCI 5V Programmable Resistor Card - Configurable Resolutions, Fully Isolated Variable Resistors, High Reliability Pickering Reed Relays. It is strongly suggested that you contact your salesman to ensure that this board will meet the requirements of your customer.  
       Silicom Ethernet
CS-SIL-PEG4 Quad-Port Copper Gigabit Ethernet Full-height PCIe Server Adapter, Broadcom-based  
       Softing CANbus
CS-SOF-CAN-AC2-PCI 2-channel intelligent CAN PCI card (requires 5V PCI slot) Driver included with RT-LAB only. RIQ required for RedHawk driver. 
       Spectracom IRIG-B
CS-SP-ANT-8225 Spectracom mast mounted GPS Antenna Only (No Receiver). Uses CS-SP-CAL700 Cable for the CS-SP-TSYNCI-PCIe device. Antenna Only - Receiver is not contained within this Antenna. 
CS-SP-CAL7100 Spectracom 100Ft GPS Antenna Cable Terminated With Type N Connectors. For use with CS-SP-ANT-8225 GPS Antenna and for the CS-SP-TSYNCI-PCIe adapter. Cable only. 
CS-SP-TPRO-PCI-66U Spectracom TPRO-PCI-66U IRIG-B Timecode Reader/Generator with PCI/PCI-X interface, Auto Detect Timecode Inputs, +/-1us Accuracy to Input, Zero Latency Time Reads, External Event Time Capture/Interrupt, Programmable Freq. Out/Interrupt, Programmable Alarm Output/Interrupt. -30C to +70C Operating Temp. No GPS or Antenna included. 
CS-SP-TSAT-PCI-66U Spectracom TSAT-PCI-66U GPS Timing Board / IRIG_B Reader/Generator with PCI/PCI-X interface, Auto Detect Timecode Inputs, +/-1us Accuracy to Input, Zero Latency Time Reads, External Event Time Capture/Interrupt, Programmable Freq. Out/Interrupt, Programmable Alarm Output/Interrupt. -30C to +70C Operating Temp.Includes mast mounted GPS receiver/antenna with 100' cable, with PVC vent pipe mast and metal straps. Includes 100' cable, Mount, and GPS Receiver/Antenna. 
CS-SP-TSYN-UPGRD Spectracom Tsync Premium Cable upgrade. This option is only valid only for purchase for the CS-SP-TSYNC-PCIe, CS-SP-TSYNCE-PCIe CS-SP-TSYNC-PCIeC and CS-SP-TSYNCI-PCIe and replaces the Basic cable included with those boards. Basic cable is not included with device when this item is purchased. 
CS-SP-TSYNC-PCIe Spectracom TSync-PCIe IRIG-B Timecode Reader/Generator with PCIe x1 interface, IRIG A, B, G, (AM or DCLS) or NASA 36, Auto Detect Timecode Inputs, +/-1us Accuracy to Input, Zero Latency Time Reads, External Event Time Capture/Interrupt, Programmable Freq. Out/Interrupt, Programmable Alarm Output/Interrupt. Includes Basic Breakout cable.  
CS-SP-TSYNC-PCIeC Spectracom TSync-PCIe (with Conformal Coating) IRIG-B Timecode Reader/Generator with PCIe x1 interface, IRIG A, B, G, (AM or DCLS) or NASA 36, Auto Detect Timecode Inputs, +/-1us Accuracy to Input, Zero Latency Time Reads, External Event Time Capture/Interrupt, Programmable Freq. Out/Interrupt, Programmable Alarm Output/Interrupt. Includes Basic Breakout cable.  
CS-SP-TSYNC-PCIeCX Spectracom TSync-PCIe-OCXO-CC (with Conformal Coating & Oven Controlled crystal oscillator) IRIG-B Timecode Reader/Generator with PCIe x1 interface, IRIG A, B, G, (AM or DCLS) or NASA 36, Auto Detect Timecode Inputs, +/-1us Accuracy to Input, Zero Latency Time Reads, External Event Time Capture/Interrupt, Programmable Freq. Out/Interrupt, Programmable Alarm Output/Interrupt. Includes Basic Breakout cable. Spectracom Optional oven-controlled crystal oscillator (OCXO) provides 2.0E-9 short term “tracking”, 5.0E-8 long term “loss of satellites” upgrade. ( Spectracom P/N Opt-OCXO ) 
CS-SP-TSYNC-PCIeX Spectracom TSync-PCIe-OCXO IRIG-B Timecode Reader/Generator with PCIe x1 interface, w/ Oven Controlled crystal oscillator (OCXO), IRIG A, B, G, (AM or DCLS) or NASA 36, Auto Detect Timecode Inputs, +/-1us Accuracy to Input, Zero Latency Time Reads, External Event Time Capture/Interrupt, Programmable Freq. Out/Interrupt, Programmable Alarm Output/Interrupt. Includes Basic Breakout cable. This item has the Spectracom Optional oven-controlled crystal oscillator (OCXO) provides 2.0E-9 short term “tracking”, 5.0E-8 long term “loss of satellites” upgrade. ( Spectracom P/N Opt-OCXO ) 
CS-SP-TSYNCE-PCIe Spectracom TSyncE-PCIe GPS Synchronized IRIG-B Timecode Reader/Generator with PCIe x1 interface, External GPS Receiver (Receiver in the Included GPS antenna) IRIG A, B, G, (AM or DCLS) or NASA 36, Auto Detect Timecode Inputs, +/-1us Accuracy to Input, Zero Latency Time Reads, External Event Time Capture/Interrupt, Programmable Freq. Out/Interrupt, Programmable Alarm Output/Interrupt. Includes Basic Breakout cable. CS-SP-TSYNCE-PCIe comes with an external GPS antenna/receiver package and antenna cable. 
CS-SP-TSYNCE-PCIeX Spectracom TSyncE-PCIe-OCXO GPS Synchronized IRIG-B Timecode Reader/Generator with PCIe x1 interface, External GPS Receiver (Receiver in the Included GPS antenna), Oven Controlled crystal oscillator (OCXO), IRIG A, B, G, (AM or DCLS) or NASA 36, Auto Detect Timecode Inputs, +/-1us Accuracy to Input, Zero Latency Time Reads, External Event Time Capture/Interrupt, Programmable Freq. Out/Interrupt, Programmable Alarm Output/Interrupt. Includes Basic Breakout cable. CS-SP-TSYNCE-PCIeX comes with an external GPS antenna/receiver package and antenna cable and has the Spectracom Optional oven-controlled crystal oscillator (OCXO) provides 2.0E-9 short term “tracking”, 5.0E-8 long term “loss of satellites” upgrade. ( Spectracom P/N Opt-OCXO ) 
CS-SP-TSYNCI-PCIe Spectracom TSyncI-PCIe GPS Synchronized IRIG-B Timecode Reader/Generator with PCIe x1 interface, IRIG A, B, G, (AM or DCLS) or NASA 36, Auto Detect Timecode Inputs, +/-1us Accuracy to Input, Zero Latency Time Reads, External Event Time Capture/Interrupt, Programmable Freq. Out/Interrupt, Programmable Alarm Output/Interrupt. Includes Basic Breakout cable (GPS Antenna/cable NOT included - See CS-SP-ANT-8225 & CS-SP-CAL7100) TSyncI-PCIe has an onboard GPS receiver compatible with the model 8225 GPS antenna and cable (sold separately). 
CS-SP-TSYNCI-PCIeX Spectracom TSyncI-PCIe-OCXO GPS Synchronized IRIG-B Timecode Reader/Generator with PCIe x1 interface, Oven Controlled crystal oscillator, IRIG A, B, G, (AM or DCLS) or NASA 36, Auto Detect Timecode Inputs, +/-1us Accuracy to Input, Zero Latency Time Reads, External Event Time Capture/Interrupt, Programmable Freq. Out/Interrupt, Programmable Alarm Output/Interrupt. Includes Basic Breakout cable (GPS Antenna/cable NOT included - See CS-SP-ANT-8225 & CS-SP-CAL7100) TSyncI-PCIe-OCXO has an onboard GPS receiver compatible with the model 8225 GPS antenna and cable (sold separately). Spectracom Optional oven-controlled crystal oscillator (OCXO) provides 2.0E-9 short term “tracking”, 5.0E-8 long term “loss of satellites” upgrade. ( Spectracom P/N Opt-OCXO ) 
CS-SP-TSYNCP-PCIe Spectracom TSync-PCIe-PTP - IRIG-B Timecode Reader/Generator, PTP IEEE-1588 Master/Slave Option with PCIe x1 interface, IRIG A, B, G, (AM or DCLS) or NASA 36, Auto Detect Timecode Inputs, +/-1us Accuracy to Input, Zero Latency Time Reads, External Event Time Capture/Interrupt, Programmable Freq. Out/Interrupt, Programmable Alarm Output/Interrupt. Includes Basic Breakout cable. No GPS. TSyncI-PCIe has an onboard GPS receiver compatible with the model 8225 GPS antenna and cable (sold separately). 
CS-SP-TSYNCP-PCIeX Spectracom TSync-PCIe-PTP-OCXO - IRIG-B Timecode Reader/Generator, PTP IEEE-1588 Master/Slave & Oven Controlled crystal oscillator (OCXO) Options with PCIe x1 interface, IRIG A, B, G, (AM or DCLS) or NASA 36, Auto Detect Timecode Inputs, +/-1us Accuracy to Input, Zero Latency Time Reads, External Event Time Capture/Interrupt, Programmable Freq. Out/Interrupt, Programmable Alarm Output/Interrupt. Includes Basic Breakout cable. No GPS. TSyncI-PCIe has an onboard GPS receiver compatible with the model 8225 GPS antenna and cable (sold separately) and the Spectracom Optional oven-controlled crystal oscillator (OCXO) provides 2.0E-9 short term “tracking”, 5.0E-8 long term “loss of satellites” upgrade. ( Spectracom P/N Opt-OCXO ) 
       Symmetricom IRIG-B
CS-SYM-BC635PCI-U (Legacy Product - Not Recommended for New Designs) Symmetricom BC635PCI-U IRIG-B Time Code Device card. Universal PCI. REQUIRES: RedHawk 5.4 or OLDER releases. Driver not valid with newer versions of RedHawk. See CS-SP-TSYNC products for alternative device. This device comes with a Binary only driver that is not supported by Concurrent Computer Corp directly. Concurrent cannot guarantee any effective response to driver issues that may occur. 
CS-SYM-BC635PCI-V2 (Legacy Product - Not Recommended for New Designs) Symmetricom BC635PCI-V2 IRIG-B Time Code Device card. Universal PCI. IRIG A, B, G, E, IEEE 1344, NASA 36, XR3 & 2137 Time Code Inputs and Outputs, 1, 5, or 10 MHz Rate Generator Output, Simultaneous AM or DCLS Time Code Inputs and Outputs. REQUIRES: RedHawk 5.4 or OLDER releases. Driver not valid with newer versions of RedHawk. See CS-SP-TSYNC products for alternative device. This device comes with a Binary only driver that is not supported by Concurrent Computer Corp directly. Concurrent cannot guarantee any effective response to driver issues that may occur. 
       Systran SCRAMNet Reflective Memory
CS-SYS-DPCIG02M-20 SCRAMNet+ SC150e Network Device 2MB SCRAMNet PCI Reflective Memory Curtis Wright requires purchase of CS-SYS-LIPCPC2S Hardware License for use with this product. 
CS-SYS-DPCIG04M-20 SCRAMNet+ SC150e Network Device 4MB SCRAMNet PCI Reflective Memory Curtis Wright requires purchase of CS-SYS-LIPCPC2S Hardware License for use with this product. 
CS-SYS-DPCIG08M-20 SCRAMNet+ SC150e Network Device 8MB SCRAMNet PCI Reflective Memory Curtis Wright requires purchase of CS-SYS-LIPCPC2S Hardware License for use with this product. 
CS-SYS-DPMCG02M-20 SCRAMNet+ SC150e Network Device 2MB SCRAMNet PMC Reflective Memory - NOTE: DMA Performance will be reduced when this card is used in conjuntion with PCI or PCIe Carrier device. Curtis Wright requires purchase of CS-SYS-LIPCPC2S Hardware License for use with this product. 
CS-SYS-DPMCG04M-20 SCRAMNet+ SC150e Network Device 4MB SCRAMNet PMC Reflective Memory NOTE: DMA Performance will be reduced when this card is used in conjuntion with PCI or PCIe Carrier device. Curtis Wright requires purchase of CS-SYS-LIPCPC2S Hardware License for use with this product. 
CS-SYS-DPMCG08M-20 SCRAMNet+ SC150e Network Device 8MB SCRAMNet PMC Reflective Memory NOTE: DMA Performance will be reduced when this card is used in conjuntion with PCI or PCIe Carrier device. Curtis Wright requires purchase of CS-SYS-LIPCPC2S Hardware License for use with this product. 
CS-SYS-FHAC-1001 Cable for the CS-SYS-GPx SCRAMNet GT200 : 10 meters, Multi-Mode Fiber Optic, Simplex, Size 50/125(um), LC-LC Connectors  
CS-SYS-FHAC-2001 Cable for the CS-SYS-GPx SCRAMNet GT200: 20 meters, Multi-Mode Fiber Optic, Simplex, Size 50/125(um), LC-LC Connectors  
CS-SYS-FHAC-3000 Cable for the CS-SYS-GPx SCRAMNet GT200: 3 meters, Multi-Mode Fiber Optic, Simplex, Size 50/125(um), LC-LC Connectors  
CS-SYS-FHAC-3001 Cable for the CS-SYS-GPx SCRAMNet GT200: 30 meters, Multi-Mode Fiber Optic, Simplex, Size 50/125(um), LC-LC Connectors  
CS-SYS-FHAC-5000 Cable for the CS-SYS-GPx SCRAMNet GT200: 5 meters, Multi-Mode Fiber Optic, Simplex, Size 50/125(um), LC-LC Connectors  
CS-SYS-GPCI-20 SCRAMNet GT200 3.3V Only PCI 128MB Dual Port Reflective Memory, 210 MB/sec data throughput for large data transfers. This card requires a 3.3V Compatible PCI slot. For 5V PCI slots use CS-SYS-GPCI5V-20. NOTE: License is included with purchase of GT200 Hardware. Curtiss Wright Hardware License is not required by Curtiss Wright with the GT200 product line. 
CS-SYS-GPCI5V-20 SCRAMNet GT200 5V PCI 128MB Dual Port Reflective Memory, up to 90 MB/sec* data throughput for large data transfers. This card is a PMC device mounted on a PCI 5V compatible carrier card. For a native 3.3V only PCI version of the GT200, please order CS-SYS-GPCI-20. NOTE: License is included with purchase of GT200 Hardware. (CW Model H-AS-GC5128SC-20 &GS p/n: PCI to PMC Adapter) *Data throughput may be limited due to PCI 5V 33MHz bus and PCI Bridge constraints. Curtiss Wright Hardware License is not required by Curtiss Wright with the GT200 product line. 
CS-SYS-GPCIE-20 SCRAMNet GT200 (PCIe x4 Compatible) 3.3V PMC 128MB Dual Port Reflective Memory on a PCIE x4 Carrier, 210 MB/sec data throughput for large data transfers. NOTE: License is included with purchase of GT200 Hardware. (CW Model H-AS-GPM128SC-20 + CCUR Model CS-GS-PMC2PCIE4) Curtiss Wright Hardware License is not required by Curtiss Wright with the GT200 product line. 
CS-SYS-GPMC-20 SCRAMNet GT200 3.3V PMC 128MB Dual Port Reflective Memory, 210 MB/sec data throughput for large data transfers. NOTE: License is included with purchase of GT200 Hardware. (CW Model H-AS-GPM128SC-20) Curtiss Wright Hardware License is not required by Curtiss Wright with the GT200 product line. 
CS-SYS-LIPCPC2S SCRAMNet+ SC150e PCI License & Documentation (NOT REQUIRED FOR GT200 boards.)  
CS-SYS-WST23001-0 SCRAMNet Multi-mode Standard Fiber Cable (30 Meters) for the CS-SYS-DPx card.  
       TZM FlexRay
CS-TZ-FLEX-PCI FlexCard PMC/PCI - 32-bit PCI-interface, 3.3V & 5V, 2MB internal RAM, FlexRay protocol version V.21, Switchable termination Resistors, 4 bus connections. Available for 32-bit systems only at this time. Cannot be purchased for 64-bit systems. Support provided through SimWB only. PMC device mounted on PMC to PCI carrier. 
       United Electronic Industries (UEI) Data Acquisition
CS-UEI-PD-CBL-40 Ribbon Cable - 40pin - 1M for the CS-UEI-PD2-DIO128I (PD-CBL-40)  
CS-UEI-PD-CONN-NI Converts 100-way NI A/D Cable to PowerDAQ 96-way analog/37-way digital (PD-CONN-NI)  
CS-UEI-PD-STP-40 40-way screw terminal panel used with Cable CS-UEI-PD-CBL-40 for the CS-UEI-PD2-DIO128i (PD-STP-40)  
CS-UEI-PD2-AO08 8-channel analog output data acquisition card. 16-bit resolution, 100 kS/s per channel update rate, three 24-bit counter/timers, 16 digital I/O lines. 5V PCI SLOT REQUIRED. (PD2-AO-8/16) Not recommended for use with SimWB due to library overhead. (CS-GS-16AOxx is recommended for SimWB). Third-party Vendor Library provided w/o enhancements or bug fixes. Customer to determine accessories appropriate for their application and external equipment. 
CS-UEI-PD2-AO16 16-channel analog output data acquisition card. 16-bit resolution, 100 kS/s per channel update rate, three 24-bit counter/timers, 16 digital I/O lines.5V PCI SLOT REQUIRED. (PD2-AO-16/16) Not recommended for use with SimWB due to library overhead. (CS-GS-16AOxx is recommended for SimWB). Third-party Vendor Library provided w/o enhancements or bug fixes. Customer to determine accessories appropriate for their application and external equipment. 
CS-UEI-PD2-AO32 32-channel analog output data acquisition card. 16-bit resolution, 100 kS/s per channel update rate, three 24-bit counter/timers, 16 digital I/O lines. 5V PCI SLOT REQUIRED. (PD2-AO-32/16) Not recommended for use with SimWB due to library overhead. (CS-GS-16AOxx is recommended for SimWB). Third-party Vendor Library provided w/o enhancements or bug fixes. Customer to determine accessories appropriate for their application and external equipment. 
CS-UEI-PD2-AO32HC 32-channel high-current analog output data acquisition card. 16-bit resolution, 100 kS/s per channel update rate, three 24-bit counter/timers, 16 digital I/O lines. 5V PCI SLOT REQUIRED. (PD2-AO-32/16HC) Not recommended for use with SimWB due to library overhead. (CS-GS-16AOxx is recommended for SimWB). Third-party Vendor Library provided w/o enhancements or bug fixes. Customer to determine accessories appropriate for their application and external equipment. 
CS-UEI-PD2-AO32HS 32-channel high-speed analog output data acquisition card. 16-bit resolution, 9.6 MS/s aggregate update rate from DSP memory, 100 kS/s per channel update rate, three 24-bit counter/timers, 16 digital I/O lines. 5V PCI SLOT REQUIRED. (PD2-AO-32/16HS) Not recommended for use with SimWB due to library overhead. (CS-GS-16AOxx is recommended for SimWB). Third-party Vendor Library provided w/o enhancements or bug fixes. Customer to determine accessories appropriate for their application and external equipment. 
CS-UEI-PD2-AO96 96-channel analog output data acquisition card. 16-bit resolution, 100 kS/s per channel update rate, three 24-bit counter/timers, 16 digital I/O lines.5V PCI SLOT REQUIRED. (PD2-AO-96/16A) Not recommended for use with SimWB due to library overhead. (CS-GS-16AOxx is recommended for SimWB). Third-party Vendor Library provided w/o enhancements or bug fixes. Customer to determine accessories appropriate for their application and external equipment. 
CS-UEI-PD2-AO96HS 96-channel high-speed analog output data acquisition card. 16-bit resolution, 6.4 MS/s aggregate update rate from DSP memory, 100 kS/s per channel update rate, three 24-bit counter/timers, 16 digital I/O lines. 5V PCI SLOT REQUIRED. (PD2-AO-96/16HS) Not recommended for use with SimWB due to library overhead. (CS-GS-16AOxx is recommended for SimWB). Third-party Vendor Library provided w/o enhancements or bug fixes. Customer to determine accessories appropriate for their application and external equipment. 
CS-UEI-PD2-AOCBL37 6ft, 37-way ribbon Cable for the CS-UEI-PD2-AOx. with mounting bracket and internal cable. This digital I/O cable set includes a 37-way internal ribbon cable with mounting bracket and a 37-way external ribbon Cable. Use this set to connect from 36-pin digital connector on any PowerDAQ AO board to any accessory with 37-pin digital connector. (PD-CBL-37-6FT) Customer to determine which accessories are appropriate to meet their application and external equipment requirements. 
CS-UEI-PD2-AOCBL96 6ft, 96-way ribbon Cablefor the CS-UEI-PD2-AOx with mounting bracket and internal cable. 96-way pinless, round shielded cable with metal cover plates. Use this cable to connect a PowerDAQ AO series board to any accessories with 96-way connector. It includes two Fujitsu FCN-247J096-G/E connectors (PD-CBL-96-6FT) Customer to determine which accessories are appropriate to meet their application and external equipment requirements. 
CS-UEI-PD2-AOKIT16 1x 1m. 96-way, round, shielded Cable with molded cover for the CS-UEI-PD2-AOx. 1x 16 channel screw terminal panel. Customer to determine which accessories are appropriate to meet their application and external equipment requirements. 
CS-UEI-PD2-AOKIT32 1x 1m. 96-way, round, shielded Cable with molded cover for the CS-UEI-PD2-AOx. 1x 32 channel screw terminal panel Customer to determine which accessories are appropriate to meet their application and external equipment requirements. 
CS-UEI-PD2-AOSTP16 The PD2-AO-STP-16 is a 16-channel screw terminal panel for the CS-UEI-PD2-AOx that includes connections to the counter/timers, high-speed interrupt/synchronization lines, both analog and digital terminals and allows you to connect analog output and sense lines directly at the screw terminals. Cable not included. Customer to determine which accessories are appropriate to meet their application and external equipment requirements. 
CS-UEI-PD2-AOSTP32 The PD2-AO-STP-32 is a 32-channel screw terminal panel for the CS-UEI-PD2-AOx that includes connections to the counter/timers, high-speed interrupt/synchronization lines, both analog and digital terminals and allows you to connect analog output and sense lines directly at the screw terminals. Cable not included. Not recommended for use with SimWB due to library overhead. (CS-GS-16AOxx is recommended for SimWB). Third-party Vendor Library provided w/o enhancements or bug fixes. Customer to determine accessories appropriate for their application and external equipment. 
CS-UEI-PD2-DIO128I 64 optoisolated digital inputs, 64 optoisolated digital outputs, Configured in ports with 16 channels, 125V isolation between ports, ports and PC, Generate interrupt on any input line, Full Length PCIx, Input Currents to 6mA, Output Currents to 500mA. Acceories: CS-UEI-PD-CBL-40, CS-UEI-PD-STP-40 Third Party Vendor Library provided w/o further enhancements or bug fixes. Customer to determine which accessories are appropriate to meet their application and external equipment requirements. 
CS-UEI-PD2-MF163H 333 kS/s, 16-bit, 16SE/8DI A/D, gains: 1,2,4,8; two 12-bit D/As; 3 counter/timers; 32 digital I/O PCI multifunction board. 5V PCI SLOT REQUIRED. (PD2-MF-16-333/16H) Not recommended for use with SimWB due to library overhead. (CS-GS-16AOxx is recommended for SimWB). Third-party Vendor Library provided w/o enhancements or bug fixes. Customer to determine accessories appropriate for their application and external equipment. 
CS-UEI-PD2-MF163L 333 kS/s, 16-bit, 16SE/8DI A/D, gains: 1,10,100,1000; two 12-bit D/As; 3 counter/timers; 32 digital I/O PCI multifunction board. 5V PCI SLOT REQUIRED. (PD2-MF-16-333/16L) Not recommended for use with SimWB due to library overhead. (CS-GS-16AOxx is recommended for SimWB). Third-party Vendor Library provided w/o enhancements or bug fixes. Customer to determine accessories appropriate for their application and external equipment. 
CS-UEI-PD2-MFS4300 300 kS/s, 16-bit, 4SE simultaneous sample & hold; two 12-bit D/As; 3 counter/timers; 32 digital I/O simultaneous sampling PCI multifunction board. 5V PCI SLOT REQUIRED. (PD2-MFS-4-300/16) Not recommended for use with SimWB due to library overhead. (CS-GS-16AOxx is recommended for SimWB). Third-party Vendor Library provided w/o enhancements or bug fixes. Customer to determine accessories appropriate for their application and external equipment. 
       Unibrain IEEE 1394
CS-UNI-1232 Unibrain Fireboard800-e V.2 3-port 1394b x1 PCIe adapter. The adapter is based on the LSI FW643 PCI Express 1394b Host Controller chipset. RedHawk Server Linux is supplied with the basic OHCI IEEE 1394 driver. An RIQ is required for any additonal Firewire device type support (i.e. Storage Media, DV, Juju, etc) 
CS-UNI-1234 Fireboard-800™ V.2 Unibrain's 3-port 1394b PCI adapter and is based on the new Texas Instruments TSB83AA23 chipset. Note: This device is a FFF replacement for the CS-UNI-1226 device. RedHawk Server Linux is supplied with the basic OHCI IEEE 1394 driver. An RIQ is required for any additonal Firewire device type support (i.e. Storage Media, DV, Juju, etc) 
CS-VMIC-2210-100 64-Channel Latching/Momentary Relay VME Board  
CS-VMIC-2510B-100 64-Bit TTL I/O Board  
CS-VMIC-3122A-000 64-Ch Differential 16-Bit High-Perf. A/D Converter VME Board  
CS-VMIC-3122A-010 32-Ch Differential16-Bit High-Perf. A/D Converter VME Board  
CS-VMIC-3122A-020 16-Ch Differential16-Bit High-Perf. A/D Converter VME Board  
CS-VMIC-4116-070 16-bit 8-channel Analog Output Board  
CS-VMIC-4132-011 12-bit 32-channel Analog Output VME Board  
       VMIC Reflective Memory (PCI)
CS-VMIC-CBL-F5-002 5' Multimode Simplex Fiber-optic Cable - LC/LC connectors. (Two required for the GE / VMIC 5565 family of boards) - (GE p/n CBL-F5-002) - This is a simplex cable, one cable is required for each node in the network. For a two node network, it is ideal to use a single Duplex cable (See CS-GE-CBL-F6-00x).  
CS-VMIC-CBL-F5-004 25' Multimode Simplex Fiber-optic Cable - LC/LC connectors. (Two required for the GE / VMIC 5565 family of boards) - This is a simplex cable, one cable is required for each node in the network. For a two node network, it is ideal to use a single Duplex cable (See CS-GE-CBL-F6-00x).  
CS-VMIC-CBL-F5-006 80' Multimode Simplex Fiber-optic Cable - LC/LC connectors. (Two required for the GE / VMIC 5565 family of boards) - This is a simplex cable, one cable is required for each node in the network. For a two node network, it is ideal to use a single Duplex cable (See CS-GE-CBL-F6-00x).  
CS-VMIC-CBL-F5-007 100' Multimode Simplex Fiber-optic Cable - LC/LC connectors. (Two required for the GE / VMIC 5565 family of boards) - This is a simplex cable, one cable is required for each node in the network. For a two node network, it is ideal to use a single Duplex cable (See CS-GE-CBL-F6-00x).  
CS-VMIPCE-5565-100 See (CS-GE-PCE-5565-100 for newer version of this card) PCIe 2.0 - 128 MB Fiber-Optic Reflective Memory w/4Kb FIFO/Multimode. NOTE: The provided driver will require additional configuration if used on systems with more than 4GB Physical Memory. Memory will need to be reserved below the 4GB memory boundary for this device. Concurrent will make these modifications to system integrated at the factory. (PCIE-5565RC-100000) The 64MB version of this product is no longer available from the vendor.  
CS-VMIPCE-5565-200 See (CS-GE-PCE-5565-200 for newer version of this card) PCIe 2.0 256 MB Fiber-Optic Reflective Memory w/4Kb FIFO/Multimode. NOTE: The provided driver will require additional configuration if used on systems with more than 4GB Physical Memory. Memory will need to be reserved below the 4GB memory boundary for this device. Concurrent will make these modifications to system integrated at the factory. (PCIE-5565RC-200000) The 64MB version of this product is no longer available from the vendor.  
       VMIC Reflective Memory (VME)
CS-VMIVME-5565-010 2 Giga Baud RM w/FO Options, 64 Mbyte Memory, 4 K FIFOs, Multimode Transmission (VMIVME  
CS-VMIVME-5565-011 2 Giga Baud RM w/FO Options, 64 Mbyte Memory, 4 K FIFOs, Single Mode Transmission  
CS-VMIVME-5565-110 2 Giga Baud RM w/FO Options, 128 Mbyte Memory, 4 K FIFOs, Multimode Transmission  
CS-VMIVME-5565-111 2 Giga Baud RM w/FO Options, 128 Mbyte Memory, 4 K FIFOs, Single Mode Transmission