Disk Drives
Tape Drive
CD ROM
Alphanumeric Terminals and Cables
Keyboard/Mouse Kit
Cabinets
Peripheral Chassis
Expansion Chassis
VME System Chassis
RA5973B-AE -- 73 GB Fixed Disk
73 GB high-performance 15K Ultra SCSI fixed disk drive for single-ended interfaces. For use on Wide 16-bit controllers only. 1-inch drive height.
Prerequisites: SCSI mounting position and a SCSI controller.
RA59146B-AE -- 146 GB Fixed Disk
146 GB high-performance 15K Ultra SCSI fixed disk drive for single-ended interfaces. For use on Wide 16-bit controllers only. 1-inch drive height.
Prerequisites: SCSI mounting position and a SCSI controller.
RA59300A-AE -- 300 GB Fixed Disk
300 GB high-performance 15K Ultra SCSI fixed disk drive for single-ended interfaces. For use on Wide 16-bit controllers only. 1-inch drive height.
Prerequisites: SCSI mounting position and a SCSI controller.
RB5973B-AE -- 73 GB Removable Disk
73 GB high-performance 15K Ultra SCSI removable disk drive for single-ended interfaces. For use on Wide 16-bit controllers only. 1-inch drive height.
Prerequisites: SCSI mounting position and a SCSI controller.
RB59146B-AE -- 146 GB Removable Disk
146 GB high-performance 15K Ultra SCSI removable disk drive for single-ended interfaces. For use on Wide 16-bit controllers only. 1-inch drive height.
Prerequisites: SCSI mounting position and a SCSI controller.
RB59300A-AE -- 300 GB Removable Disk
300 GB high-performance 15K Ultra SCSI removable disk drive for single-ended interfaces. For use on Wide 16-bit controllers only. 1-inch drive height.
Prerequisites: SCSI mounting position and a SCSI controller.
TC7100-AE -- 40 GB 4mm DDS-4 DAT Drive
Fixed 40 GB 4mm DDS-4 DAT drive with Ultra2 Wide SCSI. 3.5-inch half-height, configurable to 5.25-inch half-height. Up to 20 GB native capacity using DDS-4 cartridges holding to 40 GB compressed capacity. Sustained data transfer rate up to 330 MB/min compressed.
Prerequisites: Requires a 3.5" peripheral mounting space and SCSI interface.
Note: May be used as a data and backup device only. Not supported as a boot device.
CD ROM
RD5200-A -- CD ROM Drive
40X CD-ROM drive with SCSI interface.
Prerequisites: A 5.25-inch half-height peripheral location.
Alphanumeric Terminal
VA8692-A1 -- Alphanumeric ANSI Monochrome CRT Terminal
Alphanumeric ANSI monochrome CRT terminal. May be used as a user terminal or operators console.
Prerequisite: Requires an RS-232 cable (720-18x-90x or 730-1120531-902) and appropriate communications port.
Note: For 115V power only.
VG8692-A1 -- Graphic/Alphanumeric CRT Terminal
A Graphic/Alphanumeric CRT with a monochrome (14" non-glare, green phosphor) terminal that delivers a combination of advance capabilities, multiple terminal emulation including graphics. Terminal emulation includes the WYSE's 50/50+, 60, DEC's VT-220, VT-100, VT-52 along with TeleVideo and ADDS terminals. Graphics emulation includes Tektronix 4010/4014. The terminal has two serial ports (RS-232/423) and supports two independent and simultaneous sessions. A printer may be connected to a serial port or the included Centronics parallel port. Included standard is an ASCII keyboard with 101 keys and a tilt and swivel base for the display unit. May be used as a user terminal or operators console.
Prerequisite: Requires an RS-232 cable (720-18x-90x or 730-1120531-902), appropriate communications port, and appropriate graphics software.
Notes:
- Order model VG8692-B1 for 50 Hz version.
- VG8692 may only be available as a refurbished product. Please check with the home office regarding availabilty of new units.
Alphanumeric Terminal Cables
720-1850244-901 -- CRT Vx8692
to Async Controller 30 Foot Cable
720-1850244-903 -- CRT Vx8692 to Async Controller 50 Foot Cable
Note: The following cable is recommended for Power Hawk 6x0 and PowerStack systems.
720-1860334-901 -- 20 ft. Console cable for Vx8692 terminal
Note: The following cable is recommended for Power Hawk 700 systems.
730-1120531-902 -- 17 ft. Console cable for Vx8692 terminal
VG8200 -- Keyboard/Mouse Kit
Provides a 101-keyboard PS/2 compatible U.S. keyboard and three button mouse with cables.
VG8200B -- Keyboard/Mouse Kit (Black)
Provides a black 101-keyboard PS/2 compatible U.S. keyboard and three button mouse with cables.
SN7540-A1 -- Stand-alone 62-inch Peripheral Cabinet
Provides four device cavities for mounting tape drives, fixed and removable disk drives, and other peripheral components. It also provides mounting locations for 5 I/O Mounting Panels and cable bulkhead, an exhaust fan to provide cooling for all devices, and has been UL & FCC certified with standard peripherals. Can only be used for peripherals. CPU, VME repeater or secondary I/O chassis are not supported. Requires 120/208-VAC, 60 Hz input power. Requires 30 amp service to provide the full 20 amp AC power from the PDU. NEMA Plug #: L14-30P
Note: Order model SN7540-A2 for 50 Hz version.
SN7550-A1 -- 62" System Cabinet, 120/208V, 50 Amps
SN7515-A1 -- 62" System Cabinet, 115V, 15 AmpsSystem cabinet for housing rack-mountable CPU, secondary I/O, VME repeater chassis, and peripheral chassis. Has UL, FCC, and CSA certification with CPU systems installed. 120/208 VAC 2 Phase, 50 amps, hardwired.
Note: Order model SN7550-A2 for 50 Hz version.
System cabinet for housing rack-mountable CPU, secondary I/O, VME repeater chassis, and peripheral chassis. Has UL, FCC, and CSA certification with CPU systems installed. 115 VAC , 15 amps, hardwired.
Note: Order model SN7515-A2 for 50 Hz version.
SN7620 -- Peripheral Expansion Chassis
Supports up to seven 3.5-inch 8-bit devices with optional frames and carriers (chassis supports up to nine 3.5-inch devices with optional Expansion Kit SN7604). Devices may be swapped without powering down the system. Chassis has power and temperature monitors with alarms. Includes dual redundant power supplies, fans, and slide rails.
Location: Requires ½ of E1, Gl, G2, G3, G4, Ll, Ml, M2, M3 or M4.
Options: The chassis may be "split" to support two independent SCSI buses. (Requires two controllers and SN7604 Expansion Kit). SN7601 required if disk is to be removable (quantity one per disk).
Restrictions: Devices must be present at system boot time and may be swapped with identical drives. 5.25-inch or 3.5-inch fixed devices (not hot swappable) may be used instead of a frame and carrier (SN7601). Supports all standard fixed disks and tape units in the Product Catalog.
SN7604 -- SCSI (8-Bit) Expansion Kit for SN7620
Provides support for split SCSI (8-bit, single ended) bus on Peripheral Expansion Chassis Model #SN7620.
Prerequisite: SN7620 Peripheral Expansion Chassis.
Restrictions: Each SCSI bus may support up to seven devices (maximum of nine per chassis). Customer to provide configuration information.
SN7820 -- Peripheral Expansion Chassis 16-Bit
Supports up to nine 5.25-inch half-height 16-bit device peripheral positions. Internal cabling supports nine 16-bit SCSI devices. Includes slide-rail kit, active terminator, and 6' SCSI cable.
Location: Fast Wide SCSI controller such as the VIA or imbedded SCSI controllers on TurboHawk and Power Hawk systems. Host system must have wide SCSI connector on rear bulkhead. Requires ½ of E1, Gl, G2, G3, G4, Ll, Ml, M2, M3 or M4.
Options: The chassis may be "split" to support two independent SCSI buses. Includes required cable.
Restrictions: 8-Bit peripherals such as DATs can be used on the 16-bit SCSI bus, however SCSI ID numbers greater than 7 should not be used throughout the SCSI bus as device conflicts can result.
SN7601 -- 3.5-Inch Disk Frame & Carrier
Provides support to Hot Swap 3.5-inch disks in a chassis (SN7620). Includes a mounting frame with key-lock, drive indicator, and a carrier slide. Requires fixed disk drives.
Prerequisite: SN7620 (Peripheral Expansion Chassis), or CE0958 and CF0957, and disks.
SN7801 -- 16-Bit 3.5-Inch Disk Frame and Carrier
Provides an additional frame and carrier for a 3.5-16-Bit disk. Requires fixed 16-Bit disk drives.
SN7802 -- 16-Bit 3.5-Inch Disk Carrier
Provides an additional carrier for a 3.5-16-Bit disk. Requires fixed 16-Bit disk drives.
SN7840 -- 16-Bit Peripheral Expansion Chassis
Peripheral expansion chassis that mounts in a SN1912-Nx chassis to provide up to four 5.25" half-height peripheral positions. Internal cabling supports four 16-bit SCSI devices. Power provided by SN1912-Nx chassis.
Prerequisite: SN1912-Nx chassis with Wide SCSI controller such as the VIA or imbedded SCSI controllers on TurboHawk.
Note: For 8-bit SCSI Disks, use Model SN7620.
SN2113-A -- 21-Slot 3-Row DIN VME Expansion Chassis
SN2113-A is a 21-slot VME expansion chassis with a 3-row DIN backplane. This chassis can be used for repeater or dual I/O VME expansion. This chassis is designed to be mounted in a 19" rack. The chassis includes an auto-switching 750W power supply and fan tray. Chassis measures 14"H x 19"W x 16"D.
Prerequisite:VME Repeater Card Set (CE1100-A1) and SN7540-Ax or SN7550-Ax or a customer supplied 19" Cabinet.
Note: No peripheral mounting positions are available.
SN2115-A -- 21-Slot 5-Row DIN VME Expansion Chassis
SN2115-A is a 21-slot VME expansion chassis with a 5-row DIN backplane. This chassis can be used for repeater or dual I/O VME expansion. This chassis is designed to be mounted in a 19" rack. The chassis includes an auto-switching 750W power supply and fan tray. Chassis measures 14"H x 19"W x 16"D.
Prerequisite:VME Repeater Card Set (CE1100-A1) and SN7540-Ax or SN7550-Ax or a customer supplied 19" Cabinet.
Note: No peripheral mounting positions are available.
SO1200-AD -- Aluminum VME Filler Panel
Aluminum filler for panel for unused slots on 21-slot VME expansion chassis.
Prerequisite: SN211x-A
SO2105-A -- 21-Slot 6U VME Chassis - 5 Row Backplane
21-slot 6U VME chassis with 5-row DIN backplane and P0 support. Offers Wide/Ultra SCSI capability with four half-height drive bays located in front of the chassis. This chassis is 19" rack mountable and has a 1,000 Watt power supply. Chassis measures 19" wide x 21" high x 22" deep. Power supply is auto-ranging and accepts 90-264VAC input power. Includes filler panels as needed.
